-
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work. -
These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself. -
DESCRIPTION Supplied with 2 bearings, 12.7mm and 16mm in diameter, two shapes can produced with one cutter by changing the bearing size. The 16 mm diameter bearing removes the bottom quirk. -
British made two flute TCT bottom single or double bearing guided flush trimming cutters. Gives a superb clear finish on timber , veneers and plastic laminate. The bottom bearing is for following an edge to give a superb finish to laminates and veneers. -
DESCRIPTION Ideal for veining work, freehand decor for panels and useful for character lining work on sign writing applications in solid timbers. The angle ( measurement A ) is measured from the horizontal. TTVGC45SF-1/2, TTVGC45SF-1/4, TTVGC45SF-12, TTVGC60SF-1/2, TTVGC60SF-1/4, TTVGC60SF-12, TTVGC60SF-8 cut to a point. TTVGCB45-1/4, TTVGCB60-127-1/4 have a shank mounted bearing. -
Radiused 'V' Grooving TCT Ideal for panel and veining work, lettering, engraving, sign making, fluting, decorative trimming and barley twist. DESCRIPTION These do not cut to a point and will leave a 1mm - 2mm flat at the bottom of the groove. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
DESCRIPTION A comprehensive range of Core Box, Cove, Radius, Guttering cutters with radii from 1.6mm to 25.4mm. Cutters with part number starting TTCBB have a shank mounted bearing fitted. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation. -
Barley Twist TCT A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Can also be used for edge profiling. DESCRIPTION A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Please also see the TTGC and the Ogee range for alternative cutters that may be used for fluting. TTBTC1 - Astragal Effect gives an extra feature to turned parts. Can also be used as an edge profile or special panel effect. TTBTC2 - This Shallow Radius cutter is very popular for standard barley twist design. Ideal for use on heavy duty lathes with routing attachment. TTBTC3 - This Ovolo Cutter is a deeper version of TTBTC2. Can be used for engraving when used with a CNC router machine. TTBTC4 - This Double Radius Effect cutter can be used as an edge mould cutter. TTBTC5 - The largest Ogee Effect cutter in this range. An ideal choice for flat roping or parallel fluting. TTBTC6 - The smaller version of the TTBTC5 Ogee Cutter. Can also be used for roping effect and fluting as well as panel raising. -
The cutters still give a fantastic finish, great longevity of use and of course can be re-sharpened, a superb cutter at a very competitive price. -
PRICES REDUCED - LIMITED STOCKS Non stick Coated Tungsten Carbide Tipped Sawblades for machines up to 199mm in diameter -
DESCRIPTION Special relief on the cutter body allows for deep slotting work. Suitable for plunging. Note:LH58L, LH58L2, LH34L, not to be used in a portable router. -
A particular advantage to this replacement tip style over the conventional brazed variety is that the diameter remains constant. These double and single flute style flush trim router cutters are designed for use on template and pattern work and can be used in hand-held and table-mounted routers. They have a shank mounted bearing which will run along and follow the template which is attached to the workpiece with the end result being an exact duplicate of the template itself. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility. -
PRICES REDUCED - LIMITED STOCKS Non stick Coated Tungsten Carbide Tipped Sawblades for machines from 200mm upwards in diameter -
British made two flute TCT top bearing guided profile flush trimming cutters. Gives a superb clean finish on timber, veneers and plastic laminate. The top bearing is for following a pattern or template to give a superb finish when replicating components. -
British made TCT Trade cutters for Aquamac and Intumescent Strips. Use E207HTC for Aquamac 21, E206HTC for Aquamac 63. -
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical -
STC Spiral The accepted solid carbide cutter for machining and routing acrylics, plastics and Perspex. The helical cut gives a much easier lead into the material preventing snatching and chipping on cut. DESCRIPTION Perfect preparation before flame polishing of Perspex. Downcut for chip-free finish on MFC. DC in product code denotes Downcut. * = For use on very fine acrylics where downward cutting action will prevent vibration and component lifting. Use a P.T.F.E. spray to enhance performance and prevent waste from welding to the tool. -
SINGLE FLUTE SOLID CARBIDE For use on plastics, acrylics and light metals. The 'O' flute design reduces heat build up on low melting point materials. DESCRIPTION These straight single fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam, ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish and use the shortest cut lengths possible. The radius flute design gives effective cutting on ductile plastics, an ideal tool for cutting ABS components for example on 5 and 7 axis machines and offer efficient effective chip clearance with the for smooth feed rate that CNC's offer -
British made bearing guided chamfers with TCT tips for clean accurate cutting and fast clearance of waste materials. -
TCT Bevelled With Bottom Bearing A range of bevelled chamfer cutters with bottom guide bearing for large sections of timber, chipboard and MDF. -
Twist Drills Slow Spiral for plastics, brass, chipboard and MDF DESCRIPTION The design of the slow spiral drills are better suited for use with the counterbore and countersink ranges as they help to prevent clogging. (over the faster helix versions.) -
Planer Blades Portable TC 80.5mm and 82mm To suit every popular make of machine. DESCRIPTION To suit every popular make of machine. Prices are per pair of blades. TTKF80 suits: AEG (Atlas Copco) - 450 DEWALT - DW676K ELU MFF80/MFF40/PF161 ELU - MFF40, MFF80K, MFF80, MFF81K TTKF82N suits: AEG (Atlas Copco) - EH82, EH82.1, EH700, H822, H750, H500, EH3-82, EH800, EH450 BLACK & DECKER - BD710, DN710, DN720, BD711, KW712, KW713,KW725, BD713, BD725 BOSCH - PHO2-82, PHO3-82/B, PHO15-82, PHO16-82, PHO25-82, PHO30-82, PHO100, PHO150, PHO200, PHO300, 1592-9, GH0282, GH31-82, GHO36-82C CASALS - CE82, CE98ACE DEWALT - DW677, DW678K, DW678EK, DW680, D26500, D26501 DRAPER - PT682, P882 FELISATTI - TP282 FERM - FP82 FREUD - FE82, FE82VCE HAFFNER - FH224 HITACHI - F20*, FU20*, P20V, P20SA HOLZ-HER - 2321, 2312-S, 2322, 2223 (NEW) MAFELL - EHU82, MHU82, MHU82S, MHU82D MAKITA - M102*, 1900*, 1900B*, 1901*, 1902, 1125*, 1100*, 1923*, 1923BD, 1923H, FB080 METABO - EXPERT, 4382, HO0882, HO8382 NOTOOL - NPT82 PERLES - SK82A PEUGEOT - RA82CS, RA400, RA3/82 RYOBI - L282, L1323A*, HL-82, L-1835, L180, GH014, EPN-7582 SKIL - 92H, 94H, 95H, 96H, 97H WOLF/KANGO - 8108, 8614*, 8057 Before fitting planer blades ensure the mains supply is completely disconnected. Conversion kit required for Makita, Ryobi, Hitachi and Kango -
SINGLE FLUTE SOLID CARBIDE UPCUT SPIRAL For use on plastics, acrylics, foam, ABS, ACP and light metals. DESCRIPTION These tools are designed to give a smooth finish on hard plastics. -
Sold in boxes of 10 TC blades. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
TCT Dovetail Standard sizes for all dovetail and sliding dovetail applications ie slot dovetail, hidden dovetail, etc. DESCRIPTION Available with scribers on TTDCS14.3-8 & TTDCS127-1/4 to enable use in conjunction with portable routing jigs. Parts TTADC12B-1/4, TTBDC14B-1/4 have shank mounted bearings fitted. -
Left Hand TCT A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
TCT Undercut Groovers 4 Wing M12*1 Internal Bore Groovers 4 wing and threaded M12*1.5mm bore which enable flush recessing. The arbor and bearings are sold separately and the TTUGA arbor is for use without a bearing only, the others can be used with or without a bearing provided the correct shims are used to bring it flush at the bottom. Arbor and bearings are separate items. All prices exclude VAT. All prices exclude VAT. DESCRIPTION TTUG10, TTUG15 and TTUG20 groover can be used for fitting fire proof strip. If no bearing is used, you can use the arbor TTUGA. If bearing is to be used, use the arbors TTUGALR for all groovers except TTUG20, which requires Arbor TTUGAXLR. The following list shows the Rebate Depth obtainable with each Bearing size for a 50mm diameter groover: B25=12.5mm, B26=12mm, B28=11mm, B30=10mm, B32=9mm, B34=8mm, B36=7mm, B37=6.5mm, B42=4mm. -
With an up and downard cutting action on the one tool, the fluted compression style allows for fine finish on the top and bottom edges of the board. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand
-
Replacement Collets ER / 400E Range / DIN 6499 B -
These cutters are the perfect solution to finishing cladding and corners on pillar covering or for enhancing square table legs or returns on wall unit furniture. The diameter of the bead is twice the value of the radius i.e. R=2mm the bead diameter is 4mm. -
DESCRIPTION These cutters are designed with a plunge facility for creating slots or channels for locks and drainage. The double flute makes them more suitable for non ferrous metals. -
TCT Chamfer With Guide Pin A range of 45 and 30 degree chamfer cutters designed with a fixed small diameter guide pin. DESCRIPTION Useful for internal work where the small diameter pin enables right angle corners to be included. Popular in the sign making industry as they can chamfer the edges of plastic materials . -
REBATER WITH REPLACEMENT TC TIPS Replacement Tip Rebate 4 Wing With Bearing DESCRIPTION Replacement Tip Rebate 4 Wing With Bearing Z=Number of flutes. RPM=Maximum revolutions per minute -
STC 'Nib' Engraving Specially developed for engraving house names, bench plaques and other memorial inscriptions. The STC three flute 60 degree engraver is an ideal cutter for long production engraving work. -
TCT Groovers Light Duty 4 wing Suitable for producing biscuit jointing slots, small T&G sections and rebates, can be used with or without a bearing and multiple groovers can be mounted on the one arbor. DESCRIPTION Use TTLDTANB Arbor when no Bearing is used. Use TTLDTA Arbor with TTB16 Bearing. Z=Number of flutes. RPM=Maximum revolutions per minute Groove Depth with various bearings are as follows TTB14 = 13.6mm, TTB15 = 13.1mm, TT5/8-B16 = 12.6mm, TTB17 = 12.1mm, TTB18 = 11.6mm, TTB19 = 12.1mm, TTB20 = 10.6mm, TTB21 = 10.1mm, TTB22 = 9.6mm, TTB23 = 9.1mm, TTB24 = 8.6mm, TTB25 = 8.1mm -
Slitting saws for use with arbors TTLDTA and TTMGA6.35 When using this arbor TTMGA6.35 the screw head is only 1.5mm beyond the groover. The use of a bearing with 8 mm bore is possible on the shank side. These can be found in the bearings section through the main heading on the home page. TTLDTA Arbor inclusive spacers and bearing no. B16 (D = 16). Further bearings with bore 6,35 mm can be found in the bearings section through the main heading on the home page. -
Screws, Nuts, Washers, Allen Keys and Collars -
Box 10 Replacement Tip Turnover Knives B=30mm H=9mm S=1.5mm Cutting Edges=1 This range of Turnover Knives is used in the Titman Heavy Duty Replacement Tip Cutters. DESCRIPTION This range of Turnover Knives is used in the Titman Heavy Duty Replacement Tip Cutters. They are supplied in minimum quantities of 10 knives. TTSMG02/20, TTSMG02/30, TTSMG02/50 are manufactured from a special grade of carbide which gives a longer life when used on MDF. Not recommended for use on Chipboard. -
Drill holder for Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. DESCRIPTION Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. Available with spigot if required. TTMB10M has a 10mm thread and suits Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen machines. TTAB10M has a 10mm thread and suits Alberti, SCM, Vitap, Balestrini, Bilek, Ombe machines. TTNM8M has a 8mm thread and suits Nottmeyer machines. TTMB10BR has a 3/8 BSF thread and suits Brookman machines: TTMB10RY has a 3/8 BSW thread and suits Rye machines: Please ensure correct variation is selected when ordering. For machines not listed here please contact the Sales Department with details of thread size and type, aperture size and overall lengths for advice. -
DESCRIPTION 2 wing with centre point and with or without scribers and parallel shanks. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
Sold in boxes of 10 TC blades. -
DESCRIPTION Designed with a plunge facility for creating slots or channels for locks and drainage the relieved narrow neck section behind the cutting edge allows for a greater plunging depth. -
DESCRIPTION These cutters are designed with a plunge facility for creating slots or channels for locks and drainage. -
CT Finger Pull Grip Square Bottom For solid handles and pulls on kitchen and wall unit doors, the perfect solutions for providing positive grips and softened, easy-on-the-fingers edges without the need for external hardware. DESCRIPTION TTFPC22 is a variation of TTFPC19 giving a square bottom and undercut. Both of these have a centre tip for plunging -
TAPERED DOUBLE FLUTE TCT Two flute cutters with taper designed for constructing vacuum forming moulds. DESCRIPTION Two flute cutters with taper designed for constructing vacuum forming moulds. 2 degree tapered side allows easier release. TTH58212T can produce a leading edge on a door. -
TCT Double Flute For edging sinks and vanity bowls. The special taper on the Bearing sleeve allows for perfect guide following around the inside of the bowl. -
TCT Spoilboard For trimming bowls, trepanning and face milling. Ideal for removing flashing and large surface areas of raised draining board channels. -
DESCRIPTION -
DESCRIPTION 2 wing with or without centre point and with or without scribers, shanks are 10mm with flat on one side and end adjusting screw. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
Ideal for skimming on CNC routing machines. Tips are reversible and are sold in boxes of 10. -
MIDDLE BEARING GUIDED TOP & BOTTOM FLUSH TRIM 90 DEG TCT & RT This double flute cutter trims the top and bottom edges simultaneously as bearing follows the profile in the centre of the material. These industrial quality premium grade tungsten carbide flush trimmers are ideal for wood, plywood, MDF and other wood composites, plastics, and solid surface materials DESCRIPTION Unique in that this cutter will trim the top and bottom edges of a panel simultaneously, whilst the centrally mounted bearing follows the profile. -
Zinc coated Pocket Hole screws for use with No. 2 Robertson Screwdriver bits. These screws come in both fine and coarse thread. Fine threaded screws are for Hardwoods and the coarse threaded screws are suitable for Softwoods and man made board such as Chipboard, Plywood and MDF. -
A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation. -
TCT Double Flute Mini trimmers give a super fine finish. Ideal for cutting out small recesses in wall cladding for electrical fittings and suitable for trimming inlay flush and other trimming operations. Use TTTB22 Bearing for trimming overhanging countertops on undermount bowls. -
TCT T-Slot Square Edged Designed for creating the T-slot in wall panels used in the point of sale industry for shelving and display purposes. -
Left Hand Counter Sink TCT Designed to fit metric boring bits with 10mm Shank. Suitable for 'V' point drills, Lip and Spur and most dowel drills. DESCRIPTION Designed to fit metric boring bits with 10mm Shank. Left Hand or Right Hand rotation. Suitable for 'V' point drills, Lip and Spur and most dowel drills. TTMBC4/10 for fixing onto the Shank section, for drill diameter 4-10mm. TTMBCF range for fixing directly onto the Flute section. -
A range of lip and spur drills with 10mm diameter parallel shanks. Available with right hand rotation. -
This range are ideal for use on wood, plywood, MDF and other wood composites, plastics, and solid surface materials. Widely used for copy profiling and flush trimming, the replaceable tip design provides a constant diameter and the flexibility of instant tip changes whilst onsite. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
TCT Bullnose Staff Bead A full bullnose radius for stair treads, nosings, window boards and edge mouldings Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. -
HINGE AND FIRE STRIP RECESSER TCT A cutter ideal for hinge recessing and the underside of handrails, these have extra long shanks for use with the popular hinge jigs on the market -
TCT Corner Ovolo Profiles and moulds in one operation. Ideal for aperture cutting, ie snooker table pockets, worktops and cover mouldings. DESCRIPTION WCO Type have plunge facility. WCOB Type have bearing. -
TCT Adjustable Top and Bottom Chamfer with Bearing DESCRIPTION For bevelling and trimming the top and bottom edges of the workpiece. Adjust the four wing trimmer blocks with spacers for differing widths of material. Maximum material thickness 15mm for the DCB16 and is fixed Maximum material thickness 32mm, minimum material thickness 16mm for the BCS38. Maximum material thickness 36mm, minimum material thickness 19mm for the BGAC45. To extend the life of cutting edges use 26mm bearing. -
Universal Drill Adaptor suits 2mm diameter drill These Universal Drill Adaptors have a 10mm Shank with a flat on one side and the drill is secured with a grub screw.. DESCRIPTION These Universal Drill Adaptors have a 10mm Shank with a flat on one side and the drill is secured with a grub screw. -
TCT Double Flute Shear action downcut to reduce breakout for longer life and improved performance. Pushes waste material away from the operator. -
This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10. -
A range of Grecian and Roman Ovolo Effect cutters, essential for faithful matching of Georgian window repair or production. -
Downturn Rebate Cutter Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. Lower illustration shows method of removing bowl from worktop. DESCRIPTION To produce a 13mm rebate for the downturns on solid surface worktops. Fitted with a plastic sleeved bearing TTPB127. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
TCT Profile Edge Mould This range of edge moulding offers a varied selection of profiles for table edgings -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
TCT Slotting Ideal for slots in pencil box lids etc and internal slotting work. Suitable for intumescent fireproof strip. -
TCT Cove Mould Bearing Guided Producing a quarter round on the edge of the workpiece these are ideal for detailing casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables. DESCRIPTION These cutters come complete with TTB127 and TTB16 bearings. Matching rounding over cutters available for rule joints. -
TCT Double Flute Primarily used to produce drain board channels. For use with template and guide bush. DESCRIPTION Primarily used to produce drain board channels. For window sections, designed to help displace water and moisture off window and door frames. Can also be used as soap dish cutter. For use with template and guide bush. -
TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip.
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
TCT Undercut With Bearing A range of cutters used to produce a recess on the underside of lettering. DESCRIPTION A range of cutters used to produce a recess on the underside of lettering.
-
TCT Biscuit Joint Biscuit Joint Slotter with Arbor self guided. Comes with 3 interchangeable bearings to produce slots for the popular biscuit sizes of 0,10 and 20. Ideal for hardwood, softwoods, ply, MDF and chipboard. DESCRIPTION Z=Number of flutes. RPM=Maximum revolutions per minute Groove Depth with various bearings are as follows TTB15 = 12.5mm, TTB19 = 10.5mm, TTB23 = 8.5mm. -
British made TCT self guided corner bead cutter with two flutes for a cleaner finish. Ideal for making beautifull edge moulds for decorative finishes etc. Full corner beads can be made by making a second pass at 90 degrees. -
With either an up or downward cutting action the rougher / hogging design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action,, For use with CNC machines. -
TCT Two Flute Grooving Soft Form Single flute TCT and RT versions available. -
Tapered Repair Cutter Designed specifically to repair small imperfections in solid surface material. -
TCT Two Flute Box Cove For fine work to produce double radius in one pass, adjustable should material thicknesses vary. DESCRIPTION A further extension of the guttering cutter range with deeper cut for shallow fingerpull applications. Can also be used for cove cut on worktop upstands. For use with a template and guide bush for draining board grooves. Is suitable for producing grooves to take insulation rods. -
Countersink Shankless SS For Pillar drilling machines only, not on portables. -
A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
BALL GROOVER SINGLE FLUTE TCT A range of single flute ball slot cutters designed for pipe and cable laying into timber and MDF. DESCRIPTION Important - cut neck slot first, do not run on neck but use a side fence or guide. NB The neck does not cut. Suggested cutters for neck slot: TTM716 for TTTSB127 neck diameter 6.5mm; TTM1020 for TTTSB254 neck diameter 9.5mm; TTM1325 for TTTSB32 neck diameter 12.7mm -
This range of precision credit card stones are 1.6mm thickness means no flexing as in cheaper thinner products and are made with Monocrystaline Diamonds to give the maximum performance possible . The stones range from Extra Coarse / Coarse (180/300 grit) perfect for sharpening roughing gouges, hss hollow inserts/corning inserts, through to the woodcarvers stone which is Fine / Extra Fine (600 / 1000 grit) for precision honing and gaining bthe keenest edge on small carving tools etc. Don't forget to buy your TITMAN EDGE lapping fluid to guarantee a 5 year warranty on the stones. -
TCT Single Flute A high performance, single flute, cutter for extra clearance when cutting apertures and shaping work. The single flute gives a stronger backing support to the cutting edge. -
A range lip and spur drills with 8mm diameter parallel shanks that have an end adjusting ting screw. Available with right hand or left hand rotation. -
This range of bead cutters produce mouldings to highlight features such as fascia rails, chair backs or decorative sections 'planted' on bedroom furniture to bring a line and feature to a continuous layout. TTDSB4 is a sunken flute cutter with a shallow radius to produce a soft effect. An ideal cutter to produce fluted pillars, for fire surrounds and 'gable ends' on bedroom furniture. Useful cutter to cut on a glue joint to hide the glue line. TTDSB5 is a sunk bead mould perfect for finishing wall unit facias and cover moulds on window sections. TTDSB7 is ideal for fluting or decorating solid surrounds. -
British made bearing chamfers with 2 TCT tips for clean accurate cutting and fast clearance of waste materials. -
This range of double sided diamond bench stones range from extra Coarse & Fine 180/ 600 to the Classic Proffesional Stone which is extra fine & coarse 1000/300 grit. These Stone have a precision ground substrate ground to +/- 0.0005" and are manufactured with Monocrystaline Diamonds, making them perfect for precise sharpening of all types of tooling from Plane Irons to solid carbide tips. The Stone have clearly marked grit sizes on their surface and the extra course stone has unique clearance channels to clear away swarf and produce a keen edge fast and efficiently. The smooth continual diamond surface on the fine sides prevents snagging when sharpening small or pointed tooling. Don't forget to buy your TITMAN EDGE lapping fluid to guarantee a 5 year warranty on the stones. -
TCT Double Flute For edging sinks and vanity bowls. The special taper on the Bearing sleeve allows for perfect guide following around the inside of the bowl. -
TCT Double Flute 90 degree joint fabrication radius cutter, suitable for splashback and other 90 degree joints. -
TCT RPS Bevel Hole These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. DESCRIPTION These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. TTXC906-18 and TTXC906-23 bevel plug cutters can be used to make accurate plugs for the holes produced by the TTXC901 range of bevel hole cutters. -
TCT RPS Bevel Hole These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. DESCRIPTION These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. TTXC906-18 and TTXC906-23 bevel plug cutters can be used to make accurate plugs for the holes produced by the TTXC901 range of bevel hole cutters.
-
Shankless Counterbore For Pillar drilling machines only, not on portables. DESCRIPTION For Pillar drilling machines only, not on portables. Drills and Allen Keys not included. Available in TCT (part codes suffixed TCT) and Silver Steel (part codes suffixed SS) and to suit a selection of drill hole diameters. Please ensure correct variation is selected when ordering. -
TCT Tapered Plug Making Plug making cutter producing a tapered plug to be driven in and tightly secured. To avoid cutter deflection use this TTTPC range of cutters only on Pillar Drilling machines and do not exceed 3,000 RPM. Feed evenly into material. DESCRIPTION Plug making cutter producing a tapered plug to be driven in and tightly secured. To avoid cutter deflection use this TTTPC range of cutters only on Pillar Drilling machines and do not exceed 3,000 RPM. Feed evenly into material.
-
Turnover Knives with Cross Slot on back TC These tips are angled at the ends. Sold in boxes of 10 TC blades -
Profile Edge Mould Classic Decor TCT Bearing Guided This classic shape is a fine cutter for reproduction furniture, bolection mould and any work in which the natural finish and beauty of wood is to be enhanced. -
Ripping Saw Blade Saw Blades with anti-kickback device. Suitable for ripping hard and soft wood. DESCRIPTION Saw Blades with anti-kickback device. Suitable for ripping hard and soft wood. -
British made two flute TCT bottom bearing guided rebate cutters & stepped rebate cutter. These rebate cutters can be used for manufacturing rebates, rebated corners, lap joints, tongues etc. When a full rebate is required make two passes. -
SPOILBOARD SURFACE PLANER 2 & 3 WING TCT For trimming aluminium flashing. DESCRIPTION TTSMC20 has a shear action for finer finish. -
With either an up or downward cutting action the chipbreaker design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
TCT Four Wing Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. Lower illustration shows method of removing bowl from worktop. DESCRIPTION Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. -
Box of 10 Stair Tread Housing Replacement Tip A range of stair housing cutters in replacement tungsten carbide tip form for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand
-
A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
Ffor the popular sizes of stair treads for use in conjunction with CNC and trenching machines, cutters are offered in both left and right hand rotation. Tips are reversible and are sold in boxes of 10
-
This tool does not plunge. Tips are reversible and are sold in boxes of 10 -
Sold in boxes of 10 TC blades. -
Made from 12mm high density laminate to prevent bowing when using heavier routers, these jigs are the perfect solution for Kitchen fitters. They come with many unique features such as draining groove jig with its inset grub screws to wind down to the surface to prevent 'Dishing' when cutting the draining grooves. All manufactured with extreme precision on CNC machines in the UK by trained craftsmen for the professional tradesman. -
Specially design accessories for getting the best finish possible. The lapping fluid was specially designed over 35 years ago for the engineering industry and this original formula still out performs all others. The Mirror Paste and leather strops have been made specifically to work with each another and are all manufactured in the UK. The leather strops are double sided, Fine and Coarse, to get a superb edge when used with the Mirror Paste. The 30gms of 8000 to 10000 grit mirror finishing paste is in a screw top jar. It is an incredibly fine paste that hones and polishes knives, chisels and wood turning tools to a mirror finish and a razor like edge. -
This range of single flute RT cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design in allows a perfect V in the bottom of the groove. The tips are reversible and sold in boxes of 10. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
Replacement Collets DIN / 400E Range / OZ / DIN 6388 B Replacement Collets DESCRIPTION The DIN12 collet is suitable for Dewalt DW6275, DW629, DW624, DW625E, DW621 - ELU MOF98, MOF131, MOF177, MOF177E. FESTOOL OF1000, OF1010,OF1400, OF2000, OF2200. -
TCT Double Flute These cutters are designed to produce top surface perfect butt joints. Suitable for materials 6mm (15/64 inch) to 17mm (43/64 inch) thick. -
TCT Double Flute Fitted with self-guiding Bearing for rounding over. See cutters TTXC301 and TTXC321 for complete rounding over. -
TCT Two Flute Bowl Aperture Trimmer Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. DESCRIPTION Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
SINKING AND STRIP RECESSING TCT For library and book shelving strip/tonk strip. -
UP/DOWN SHEAR STAGGERED TOOTH TCT A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. DESCRIPTION A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
TCT Ogee Used for paneling and edge moulding for that classic ogee feature. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
TCT Raised Panel Grecian Ogee Ideal for heavy cornice and dado rail production. Used in restoration and as a classic mould for picture frames, to produce raised panels on drawer fronts and doors. -
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
DOWNCUT SHEAR DOUBLE FLUTE TCT Shear action downcut to reduce breakout. DESCRIPTION For short producton runs only. For longer and improved performance see our Solid Carbide Range. *These tools are designed to give a 'tear' free groove in conjunction with a tight housed joint when using plywood. -
Profile Edge Mould Decorative TCT The TTDEC range of tools are perfect for enhancing the appearance of square edged timber many of which offer balanced moulds for use on sections of woodwork at the centre of the design. -
Left Hand Rotation 3 Wing With 3 Scribers and Centre Point A comprehensive range of hinge borers. Please ensure correct variation is selected when ordering. DESCRIPTION A comprehensive range of hinge borers. All are available in 57mm overall lengths. Some 2 wing with 2 scribers cutters are also available in 70mm and 77mm overall lengths. All have 10mm diameter Left Hand or Right Hand Shanks. Shanks have flat on one side and length adjusting screw. Some sizes are also available with or without centre point. The TTTMB range have a removable/replaceable centre point with a 'V' point effect at one end, flush finish at the other end. Please ensure correct variation is selected when ordering. For use on Multi-Boring machines. -
2 Wing with C/Point without Scribers TCT 2 wing available with or without scribers and parallel shanks. DESCRIPTION 2 wing available with or without scribers and parallel shanks. Right hand with centre point. Left hand available to special order - please contact the Sales Department for details. For boring bits at above 80mm overall length please contact the Sales Department for pricing and availability. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Select correct boring bit design for machine, material and thickness: Drill or Boring Machines: Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM.
-
Groover TCT Titman's Wobble Saw is the traditional answer to the problem of cutting various widths of grooves in timber, chipboard and other man-made materials. DESCRIPTION Titman's Wobble Saw is the traditional answer to the problem of cutting various widths of grooves in timber, chipboard and other man-made materials. The steel boss and blade vary the Kerf from 6mm to 22mm when set to the calibrated reading. The eight tunsten carbide tips have a shear action to give a clean and precise groove width. Varied bore sizes can be offered. Please state requirements when ordering. -
These cutters can be used as matched sets of flute and beads or as individual sunk bead and reads. TTDSB8, TTDSB9 and TTDSB10 are suitable for moulding table surrounds and capillary drip grooves for window surrounds. TTRDSB8, TTRDSB9 and TTRDSB10 are matched to the TTDSB8, TTDSB9 and TTDSB10 range for the production of strip planking. -
British made TCT Cove Cutters with two flutes for a cleaner finish. Ideal for making radiused grooves for decorative finishes etc. When making deeper channels take several passes. -
British made Tungsten Carbide Tipped Dovetail cutters with differing angles and length of cut to produce accurate joints time and again for making furniture, drawers & boxes etc. -
A two port pocket hole jig kits suitable for every need. The four port jig has 12 pre-set hole configurations for joining timber from 12.7 to 38mm thick. All jigs and drill bits have pre set markings etched on them for fast, efficient and accurate setup. -
An absolute must for the user of Multi Function Tables (MFT). This compact yet precision made jig ensures the fast reliable reproduction of MFT table tops over and over again. The Aluminium dogs are precision ground to ensure a tight fit to ensure accuracy. Use with the Titman 46DHTC Router cutter to ensure the perfect aperture every time. Made from High pressure laminate for accuracy and durability. Part number EDOG comes as a pair of aluminium dogs for using with EMFTJIG, ECSJIG or any MFT table with 20mm openings. -
Tips are reversible and are sold in boxes of 10. -
Angles are measured from the horizontal. Tips are reversible and are sold in boxes of 10. -
TCT Double Flute For creating a 'step down' shadow line between bowl and sheet. -
TCT Double Flute TTXC611 is the perfect cutter for panel raising work. TTXC616 is designed for large 45 degree chamfer work with guide Bearing. -
TCT Double Flute This cutter produces a 'waterfall' effect on a worktop. Can be used against a wall for splashback. -
TCT Double Flute Great care should be exercised when using this cutter to avoid 'cutter wander'. Use correct jig, template or side fence. Use a guide bush in conjunction with an offset template. -
TCT Two Flute Hob Cutter Used to produce, in one pass, the aperture in which the hob unit sits. -
7 PIECE TCT RPS Cutter Set 1/2 Shanks Specially made tooling for repair of 'wrongly made' holes and also for decorative effects using plugs in other colours. This set includes all the TTXC901 and TTXC906 cutters. DESCRIPTION Use the Titman Plug system for a perfect repair. Specially made tooling for repair of 'wrongly made' holes and also for decorative effects using plugs in other colours. This set includes all the TTXC901 and TTXC906 cutters. -
TCT Weatherseal Recessing & Seals The perfect weatherstrip cutter, ideal for use with a portable router on site. DESCRIPTION TTWSC2 is used without a bearing. TTWSC3 has a 90mm overall length to suit 40-50mm rebate on doors. TTWSC4 routs a 2.7mm groove, 6mm deep. TTWSC5 suits the slot seal Carripile I weatherstrip system. TTSSC1 is a Smoke Seal cutter, designed to run off the bearing and give correct depth of cut to take a Quick Fit Smoke Seal Strip. -
TC Replacement Tip for 'V' Grooving & Tracey Work With special programming, the TTVGC-RT range of cutters can produce a perfect right-angle corner. DESCRIPTION Using a normal angle cutter, the corners produced have a radius. With special programming, the TTVGC-RT range of cutters can produce a perfect right-angle corner. Reversible Knives are 12mm wide D mm and L mm values given are maximums.
-
TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section. -
Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings. -
TCT Minature Bead Cutters A range of minature beading cutters for fine decorative work. These cutters perform best at 24,000 RPM. -
Right Hand Drill TCT Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter. Drilling machines only - not for use on portables. DESCRIPTION Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter (see below). Drilling machines only - not for use on portables. All drills 20mm long. TTCSD8 (1/4 inch Shank) and TTCSD9.5 (10mm Shank): Countersink Diameter D=9.5mm (matches plug produced by TTPMC8), Drill Diameter d=4.8mm, No. 8 Wood Screw TTCSD10 (1/4 inch Shank) and TTCSD12 (10mm Shank): Countersink Diameter D=12mm (matches plug produced by TTPMC10), Drill Diameter d=5.5mm, No. 10 Wood Screw TTCSD12 (1/4 inch Shank) and TTCSD16 (10mm Shank): Countersink Diameter D=16mm (matches plug produced by TTPMC12), Drill Diameter d=6.35mm, No. 12 Wood Screw -
TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes. -
TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
A unique cutter that will trim the top and bottom edges of a panel simultaneously, the centrally mounted bearing follows the profile. Tips are reversible and are sold in boxes of 10. -
Profile Edge Mould Classic Lambs Tongue TCT Bearing Guided Classic Lambs Tongue mould perfect for finishing table and furniture tops. DESCRIPTION These cutters are supplied with a 9.5mm diameter bearing and a 12.7mm diameter bearing. -
TCT Chamfering Edge Chamfering Edge Cutters. Reducing and Chamfering. DESCRIPTION TTCEC45, TTCECR45, TTLTC4, TTLTCR4, TTLTC63, TTLTCR63 are non plunge but with bottom cut facility. TTCECR45 is the reverse of TTCEC45. TTCECR45L is the reverse of TTCEC45L. TTLTC4 and TTLTCR4 give a lambs tongue effect as TTROB range. TTLTCR4 is the reverse of TTLTC4. TTLTCR63 is the reverse of TTLTC63. -
British made Hinge Sink and Keyhole cutters. Specialist cutters to get a specific job done. These cutters have Tungsten Carbide tips to leave a clean finish to your workpiece. -
All these blades have a positive cutting angle which make them suitable for wood and wood composites. To be used on portable machines and mitre saws. Excelent for cutting across the grain. All these blades are alternate top bevel (ATB) and Tungsten carbide Tipped (TCT). -
These scoring blades are ideal for Laminates, Bi Laminates and Veneers. They have an ATB tooth with a 5 degree positive cutting angle. Maximum scoring depth 2mm. For Scoring Melemine on bilaminated chipboard and MDF panels. All these blades are alternate top bevel (ATB) and Tungsten carbide Tipped (TCT). -
Precision ground diamond Pen files and Needle Files. The pen files are suitable for sharpening fishing hooks, darts, hunting knives etc. whilst the set of 4 needle are the ideal tool for sharpening carving tools etc and are also used in the British Aerospace industry. This range is a truly versatile set of pocket files that are electroplated with Monocrystalline Diamonds to enhamce performance. The pen style files simply unscrew from their case and screw back onto the case to make a steel type file for sharpening Knives, fishing hooks, dart points 600 Grit. Guaranteed for 5 years when used with TITMAN EDGE lapping fluid. -
Produces a slot to take inlays of a different col0ur to produce a line effect joint -
This range of single flute replacement tip cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. The TC tips are non reversible and are sold singularly. -
A range of rebate cutters bearing guided, bearings can be changed to a different diameter to produce various rebate depths. The TTRCB95-1/2RT and TTRCB95-8RT are fitted with the TT3/8-B37514 bearing and also come with the TT1/2-B127, TTB15 and TTB19 bearings. The TTRCb9512RT is fitted with 2 - TT1/2-B127 bearings and can then be used in conjunction with the TTRR range of aluminium sleeves to produce the various rebate depths. These rings are placed in the middle of the 2 bearings which then keep them secure whilst routing. If you take the diameter dimension of the cutter minus the diameter dimension of the ring and divide by 2 this will give you the rebate depth. Tips are reversible and are sold in boxes of 10 -
Allan Keys and Torx Drivers
-
TCT Double Flute Helps to reduce the effect of overlay joint line. DESCRIPTION Sometimes called 'waterfall effect' giving a non-drip edge to a worktop. TTXC214 has a shorter cut length, ideal for use on 12.5mm thick material. TTXC216 is fitted with self-guided Bearing for use with 15mm thick material. TTXC221 is ideal for use on 19mm (3/4 inch) thick material. -
TCT Two Flute Ventilation Slot Slots and produces a radius on the upper edge in one pass. -
TCT Two Flute Adjustable Double Radius Use with 1/2 inch thick material produces double radius in one pass. -
TCT Two Flute Rounding Over Fitted with a Shank mounted Bearing. First cut with TTXC301, finshing using matching TTXC321. Eliminates flat on edge. -
TCT Two Flute Spanish Edge with Bearing For all types of decorative edge profiling. -
TCT Double Flute For bevelling inside bowl tops and similar applications. Avoids need to turn workpiece. -
DESCRIPTION This cutter is used to enhance the edge of the worktop -
TCT Four Flute Cutter For grooving and heavy rebate work. -
TCT Two Flute Cove Mould With Bearing Two flute half round cutter. Ideal for a scalloped edge finish. For all types of decorative edge profiling. -
TCT RPS Bevel Hole These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. DESCRIPTION These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. TTXC906-18 and TTXC906-23 bevel plug cutters can be used to make accurate plugs for the holes produced by the TTXC901 range of bevel hole cutters. -
Weatherstrip Cutters A range of cutters designed to make the fitting of weatherstrip to door and window frames quick and easy. -
TCT Capillary Water Channel Groove All cutters in this range are non plunging but with bottom cutting action. DESCRIPTION This is designed to place a capillary groove on sill sections when used on site in a portable machine. -
TCT Multi-Mould DESCRIPTION TTTOR25 gives an ornate moulding used in full or in part. TTTOR22 is a possible picture rail and cover mould cutter. TTTOR27 ideal to use the complete mould or part for short production runs. Excellent cutter to produce ornate skirting and architrave moulding. TTTOR-B gives a deep cavetto effect with a bead to break up the line of the mould. The fine lines of this cutter make it an excellent choice for matching skirting and architrave. TTTOR-C is a variation of the Torus Mould (TTTOR-T). -
DESCRIPTION To achieve a perfect tongued and grooved joint for flooring and paneling use the TTFFC28 in conjunction with a TTG35552-6.35 mini groover ( for the groove ). The same arbor can be used for the TTFFC28 and TTFA20 The TTFA20 is also for use with the TTLDTA style of arbor. -
DESCRIPTION Water slot range of cutters with single straight flute design and a shorter relief slot on opposite side of cutting edge to assist plunging. -
DESCRIPTION Made from solid tungsten carbide these are designed with a plunge facility for creating slots or channels for locks and drainage. -
TCT Stair Nosing This range have a flatter style to a standard full bull nose offering an alternative profile on stair treads, window boards and these can also be used to relieve sharp corners on the standard board thickness. DESCRIPTION The TTSNCB10 has a bottom bearing. -
Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006
-
TCT Machine Countersink & Bores A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
CT Plug Making Drilling machines only. DESCRIPTION Drilling machines only. Can be used with the CSD range of Countersink Drills and CBD range of Counterbore Drills. Maximum Plug Depth=16mm for all cutters. TTPMC8 Plug Diameter=9.5mm, No. 8 Wood Screw TTPMC9 Plug Diameter=10mm TTPMC10 Plug Diameter=12mm, No. 10 Wood Screw TTPMC127 Plug Diameter=12.7mm TTPMC12 Plug Diameter=16mm, No. 12 Wood Screw -
The Titman Multi-Profiler Cutterhead is designed to take the popular WS 40m and 50mm cutter profiles. Using two location pins and a recessed locking flange, the Multi-Profiler is easily changed and secured, offering a whole range of standard and special profiles (specials on request). THIS IS FOR THE TOOL BODY ONLY. A large range of blades are available, download the catalogue pdf on our website, part codes TTFK000 to TTFK100 for blades and TTDK000 to TTDK100 for defectors. -
Pin diameter is 5.5mm by 5.5mm long
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
RouterBorer These are a designed for use at a faster RPM than standard boring bits for recessing circular hinges. A template and a guide will ensure accurate hole placement on the workpiece and that the router itself is secure with no sideways movement DESCRIPTION The CB version have chip breakers for use on more fibrous materials. The design allows the tool to run at speeds of 1000-20,000 RPM. -
A range drills with a 1mm long 45 degree chamfer on the tip edge for use in the specialized boring machine MAFELL DuoDübler . Shanks are 8mm diameter with a flat on one side and length adjusting screw in the end. Available with right hand. -
These cutter are double flute and they are non plunging with an outside fixing style for the use of profiling, the tips have 4 cutting edges so they can also be ramped down into workpiece. Tips are reversible and are sold in boxes of 10 -
STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish.
-
TCT Classical Perfect for drawer fronts in solid material for enhancing the style and appearance of panelled work. -
TCT Capillary Groove Capillary groove cutters for sills and window sections. DESCRIPTION TTUSD36 for use with the Schlegel Q-LON weatherstrip. -
Turnover Knife Angled Ends Box 10 This range of Turnover Knives is used in the Titman Heavy Duty Replacement Tip Cutters. DESCRIPTION This range of Turnover Knives is used in the Titman Heavy Duty Replacement Tip Cutters. They are supplied in minimum quantities of 10 knives. TTSMG02/20, TTSMG02/30, TTSMG02/50 are manufactured from a special grade of carbide which gives a longer life when used on MDF. Not recommended for use on Chipboard.
-
TCT Bevelled With Bottom Radius A range of bevelled cutters with a bottom radius ideal for scallop fluting and finger pull applications.
-
Used to create a fluting effect on the edge of furniture. TTRWHC range are used to create a fluting effect on the edge of furniture. TTSBCB range has a removeable bearing system. When requiring a self guiding effect ensure the jig has clearance between workpiece and bottom of cutter. TTHHC20 and TTRHHC20 complement each other and when used together perform the cuts needed to form a drop leaf table joint. Please note some of these products are Made To Order. -
British made Hinge Sink and Keyhole cutters. Specialist cutters to get a specific job done. These cutters have Tungsten Carbide tips to leave a clean finish to your workpiece.
-
150mm Robertson No.2 Pocket hole screwdriver bits, HSS Hex or standard shank pocket hole drills with collet and hex keys.
-
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge.
-
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work.
-
These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself.
-
DESCRIPTION Supplied with 2 bearings, 12.7mm and 16mm in diameter, two shapes can produced with one cutter by changing the bearing size. The 16 mm diameter bearing removes the bottom quirk.
-
British made two flute TCT bottom single or double bearing guided flush trimming cutters. Gives a superb clear finish on timber , veneers and plastic laminate. The bottom bearing is for following an edge to give a superb finish to laminates and veneers.
-
DESCRIPTION Ideal for veining work, freehand decor for panels and useful for character lining work on sign writing applications in solid timbers. The angle ( measurement A ) is measured from the horizontal. TTVGC45SF-1/2, TTVGC45SF-1/4, TTVGC45SF-12, TTVGC60SF-1/2, TTVGC60SF-1/4, TTVGC60SF-12, TTVGC60SF-8 cut to a point. TTVGCB45-1/4, TTVGCB60-127-1/4 have a shank mounted bearing.
-
Radiused 'V' Grooving TCT Ideal for panel and veining work, lettering, engraving, sign making, fluting, decorative trimming and barley twist. DESCRIPTION These do not cut to a point and will leave a 1mm - 2mm flat at the bottom of the groove.
-
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines.
-
DESCRIPTION A comprehensive range of Core Box, Cove, Radius, Guttering cutters with radii from 1.6mm to 25.4mm. Cutters with part number starting TTCBB have a shank mounted bearing fitted.
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
Barley Twist TCT A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Can also be used for edge profiling. DESCRIPTION A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Please also see the TTGC and the Ogee range for alternative cutters that may be used for fluting. TTBTC1 - Astragal Effect gives an extra feature to turned parts. Can also be used as an edge profile or special panel effect. TTBTC2 - This Shallow Radius cutter is very popular for standard barley twist design. Ideal for use on heavy duty lathes with routing attachment. TTBTC3 - This Ovolo Cutter is a deeper version of TTBTC2. Can be used for engraving when used with a CNC router machine. TTBTC4 - This Double Radius Effect cutter can be used as an edge mould cutter. TTBTC5 - The largest Ogee Effect cutter in this range. An ideal choice for flat roping or parallel fluting. TTBTC6 - The smaller version of the TTBTC5 Ogee Cutter. Can also be used for roping effect and fluting as well as panel raising.
-
The cutters still give a fantastic finish, great longevity of use and of course can be re-sharpened, a superb cutter at a very competitive price.
-
PRICES REDUCED - LIMITED STOCKS Non stick Coated Tungsten Carbide Tipped Sawblades for machines up to 199mm in diameter
-
DESCRIPTION Special relief on the cutter body allows for deep slotting work. Suitable for plunging. Note:LH58L, LH58L2, LH34L, not to be used in a portable router.
-
A particular advantage to this replacement tip style over the conventional brazed variety is that the diameter remains constant. These double and single flute style flush trim router cutters are designed for use on template and pattern work and can be used in hand-held and table-mounted routers. They have a shank mounted bearing which will run along and follow the template which is attached to the workpiece with the end result being an exact duplicate of the template itself. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10.
-
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility.
-
PRICES REDUCED - LIMITED STOCKS Non stick Coated Tungsten Carbide Tipped Sawblades for machines from 200mm upwards in diameter
-
British made two flute TCT top bearing guided profile flush trimming cutters. Gives a superb clean finish on timber, veneers and plastic laminate. The top bearing is for following a pattern or template to give a superb finish when replicating components.
-
British made TCT Trade cutters for Aquamac and Intumescent Strips. Use E207HTC for Aquamac 21, E206HTC for Aquamac 63.
-
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical
-
STC Spiral The accepted solid carbide cutter for machining and routing acrylics, plastics and Perspex. The helical cut gives a much easier lead into the material preventing snatching and chipping on cut. DESCRIPTION Perfect preparation before flame polishing of Perspex. Downcut for chip-free finish on MFC. DC in product code denotes Downcut. * = For use on very fine acrylics where downward cutting action will prevent vibration and component lifting. Use a P.T.F.E. spray to enhance performance and prevent waste from welding to the tool.
-
SINGLE FLUTE SOLID CARBIDE For use on plastics, acrylics and light metals. The 'O' flute design reduces heat build up on low melting point materials. DESCRIPTION These straight single fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam, ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish and use the shortest cut lengths possible. The radius flute design gives effective cutting on ductile plastics, an ideal tool for cutting ABS components for example on 5 and 7 axis machines and offer efficient effective chip clearance with the for smooth feed rate that CNC's offer
-
British made bearing guided chamfers with TCT tips for clean accurate cutting and fast clearance of waste materials.
-
TCT Bevelled With Bottom Bearing A range of bevelled chamfer cutters with bottom guide bearing for large sections of timber, chipboard and MDF.
-
Twist Drills Slow Spiral for plastics, brass, chipboard and MDF DESCRIPTION The design of the slow spiral drills are better suited for use with the counterbore and countersink ranges as they help to prevent clogging. (over the faster helix versions.)
-
Planer Blades Portable TC 80.5mm and 82mm To suit every popular make of machine. DESCRIPTION To suit every popular make of machine. Prices are per pair of blades. TTKF80 suits: AEG (Atlas Copco) - 450 DEWALT - DW676K ELU MFF80/MFF40/PF161 ELU - MFF40, MFF80K, MFF80, MFF81K TTKF82N suits: AEG (Atlas Copco) - EH82, EH82.1, EH700, H822, H750, H500, EH3-82, EH800, EH450 BLACK & DECKER - BD710, DN710, DN720, BD711, KW712, KW713,KW725, BD713, BD725 BOSCH - PHO2-82, PHO3-82/B, PHO15-82, PHO16-82, PHO25-82, PHO30-82, PHO100, PHO150, PHO200, PHO300, 1592-9, GH0282, GH31-82, GHO36-82C CASALS - CE82, CE98ACE DEWALT - DW677, DW678K, DW678EK, DW680, D26500, D26501 DRAPER - PT682, P882 FELISATTI - TP282 FERM - FP82 FREUD - FE82, FE82VCE HAFFNER - FH224 HITACHI - F20*, FU20*, P20V, P20SA HOLZ-HER - 2321, 2312-S, 2322, 2223 (NEW) MAFELL - EHU82, MHU82, MHU82S, MHU82D MAKITA - M102*, 1900*, 1900B*, 1901*, 1902, 1125*, 1100*, 1923*, 1923BD, 1923H, FB080 METABO - EXPERT, 4382, HO0882, HO8382 NOTOOL - NPT82 PERLES - SK82A PEUGEOT - RA82CS, RA400, RA3/82 RYOBI - L282, L1323A*, HL-82, L-1835, L180, GH014, EPN-7582 SKIL - 92H, 94H, 95H, 96H, 97H WOLF/KANGO - 8108, 8614*, 8057 Before fitting planer blades ensure the mains supply is completely disconnected. Conversion kit required for Makita, Ryobi, Hitachi and Kango
-
SINGLE FLUTE SOLID CARBIDE UPCUT SPIRAL For use on plastics, acrylics, foam, ABS, ACP and light metals. DESCRIPTION These tools are designed to give a smooth finish on hard plastics.
-
Sold in boxes of 10 TC blades.
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
TCT Dovetail Standard sizes for all dovetail and sliding dovetail applications ie slot dovetail, hidden dovetail, etc. DESCRIPTION Available with scribers on TTDCS14.3-8 & TTDCS127-1/4 to enable use in conjunction with portable routing jigs. Parts TTADC12B-1/4, TTBDC14B-1/4 have shank mounted bearings fitted.
-
Left Hand TCT A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price.
-
TCT Undercut Groovers 4 Wing M12*1 Internal Bore Groovers 4 wing and threaded M12*1.5mm bore which enable flush recessing. The arbor and bearings are sold separately and the TTUGA arbor is for use without a bearing only, the others can be used with or without a bearing provided the correct shims are used to bring it flush at the bottom. Arbor and bearings are separate items. All prices exclude VAT. All prices exclude VAT. DESCRIPTION TTUG10, TTUG15 and TTUG20 groover can be used for fitting fire proof strip. If no bearing is used, you can use the arbor TTUGA. If bearing is to be used, use the arbors TTUGALR for all groovers except TTUG20, which requires Arbor TTUGAXLR. The following list shows the Rebate Depth obtainable with each Bearing size for a 50mm diameter groover: B25=12.5mm, B26=12mm, B28=11mm, B30=10mm, B32=9mm, B34=8mm, B36=7mm, B37=6.5mm, B42=4mm.
-
With an up and downard cutting action on the one tool, the fluted compression style allows for fine finish on the top and bottom edges of the board. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines.
-
TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand