-
TCT Bevelled With Bottom Radius A range of bevelled cutters with a bottom radius ideal for scallop fluting and finger pull applications. -
TCT Bevelled With Bottom Bearing A range of bevelled chamfer cutters with bottom guide bearing for large sections of timber, chipboard and MDF. -
This tool does not plunge. Tips are reversible and are sold in boxes of 10 -
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical -
BALL GROOVER SINGLE FLUTE TCT A range of single flute ball slot cutters designed for pipe and cable laying into timber and MDF. DESCRIPTION Important - cut neck slot first, do not run on neck but use a side fence or guide. NB The neck does not cut. Suggested cutters for neck slot: TTM716 for TTTSB127 neck diameter 6.5mm; TTM1020 for TTTSB254 neck diameter 9.5mm; TTM1325 for TTTSB32 neck diameter 12.7mm -
TCT Undercut Groovers 4 Wing M12*1 Internal Bore Groovers 4 wing and threaded M12*1.5mm bore which enable flush recessing. The arbor and bearings are sold separately and the TTUGA arbor is for use without a bearing only, the others can be used with or without a bearing provided the correct shims are used to bring it flush at the bottom. Arbor and bearings are separate items. All prices exclude VAT. All prices exclude VAT. DESCRIPTION TTUG10, TTUG15 and TTUG20 groover can be used for fitting fire proof strip. If no bearing is used, you can use the arbor TTUGA. If bearing is to be used, use the arbors TTUGALR for all groovers except TTUG20, which requires Arbor TTUGAXLR. The following list shows the Rebate Depth obtainable with each Bearing size for a 50mm diameter groover: B25=12.5mm, B26=12mm, B28=11mm, B30=10mm, B32=9mm, B34=8mm, B36=7mm, B37=6.5mm, B42=4mm. -
TCT Groovers Light Duty 4 wing Suitable for producing biscuit jointing slots, small T&G sections and rebates, can be used with or without a bearing and multiple groovers can be mounted on the one arbor. DESCRIPTION Use TTLDTANB Arbor when no Bearing is used. Use TTLDTA Arbor with TTB16 Bearing. Z=Number of flutes. RPM=Maximum revolutions per minute Groove Depth with various bearings are as follows TTB14 = 13.6mm, TTB15 = 13.1mm, TT5/8-B16 = 12.6mm, TTB17 = 12.1mm, TTB18 = 11.6mm, TTB19 = 12.1mm, TTB20 = 10.6mm, TTB21 = 10.1mm, TTB22 = 9.6mm, TTB23 = 9.1mm, TTB24 = 8.6mm, TTB25 = 8.1mm -
Sold in boxes of 10 TC blades. -
This range are ideal for use on wood, plywood, MDF and other wood composites, plastics, and solid surface materials. Widely used for copy profiling and flush trimming, the replaceable tip design provides a constant diameter and the flexibility of instant tip changes whilst onsite. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
Universal Drill Adaptor suits 2mm diameter drill These Universal Drill Adaptors have a 10mm Shank with a flat on one side and the drill is secured with a grub screw.. DESCRIPTION These Universal Drill Adaptors have a 10mm Shank with a flat on one side and the drill is secured with a grub screw. -
Drill holder for Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. DESCRIPTION Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. Available with spigot if required. TTMB10M has a 10mm thread and suits Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen machines. TTAB10M has a 10mm thread and suits Alberti, SCM, Vitap, Balestrini, Bilek, Ombe machines. TTNM8M has a 8mm thread and suits Nottmeyer machines. TTMB10BR has a 3/8 BSF thread and suits Brookman machines: TTMB10RY has a 3/8 BSW thread and suits Rye machines: Please ensure correct variation is selected when ordering. For machines not listed here please contact the Sales Department with details of thread size and type, aperture size and overall lengths for advice. -
TCT Weatherseal Recessing & Seals The perfect weatherstrip cutter, ideal for use with a portable router on site. DESCRIPTION TTWSC2 is used without a bearing. TTWSC3 has a 90mm overall length to suit 40-50mm rebate on doors. TTWSC4 routs a 2.7mm groove, 6mm deep. TTWSC5 suits the slot seal Carripile I weatherstrip system. TTSSC1 is a Smoke Seal cutter, designed to run off the bearing and give correct depth of cut to take a Quick Fit Smoke Seal Strip. -
TCT Capillary Water Channel Groove All cutters in this range are non plunging but with bottom cutting action. DESCRIPTION This is designed to place a capillary groove on sill sections when used on site in a portable machine. -
Box 10 Replacement Tip Turnover Knives B=30mm H=9mm S=1.5mm Cutting Edges=1 This range of Turnover Knives is used in the Titman Heavy Duty Replacement Tip Cutters. DESCRIPTION This range of Turnover Knives is used in the Titman Heavy Duty Replacement Tip Cutters. They are supplied in minimum quantities of 10 knives. TTSMG02/20, TTSMG02/30, TTSMG02/50 are manufactured from a special grade of carbide which gives a longer life when used on MDF. Not recommended for use on Chipboard. -
TC Replacement Tip for 'V' Grooving & Tracey Work With special programming, the TTVGC-RT range of cutters can produce a perfect right-angle corner. DESCRIPTION Using a normal angle cutter, the corners produced have a radius. With special programming, the TTVGC-RT range of cutters can produce a perfect right-angle corner. Reversible Knives are 12mm wide D mm and L mm values given are maximums. -
A particular advantage to this replacement tip style over the conventional brazed variety is that the diameter remains constant. These double and single flute style flush trim router cutters are designed for use on template and pattern work and can be used in hand-held and table-mounted routers. They have a shank mounted bearing which will run along and follow the template which is attached to the workpiece with the end result being an exact duplicate of the template itself. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
DESCRIPTION Water slot range of cutters with single straight flute design and a shorter relief slot on opposite side of cutting edge to assist plunging. -
DESCRIPTION Designed with a plunge facility for creating slots or channels for locks and drainage the relieved narrow neck section behind the cutting edge allows for a greater plunging depth. -
DESCRIPTION These cutters are designed with a plunge facility for creating slots or channels for locks and drainage. The double flute makes them more suitable for non ferrous metals. -
DESCRIPTION Made from solid tungsten carbide these are designed with a plunge facility for creating slots or channels for locks and drainage. -
DESCRIPTION These cutters are designed with a plunge facility for creating slots or channels for locks and drainage. -
TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand -
Box of 10 Stair Tread Housing Replacement Tip A range of stair housing cutters in replacement tungsten carbide tip form for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand -
Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006
-
TCT Slotting Ideal for slots in pencil box lids etc and internal slotting work. Suitable for intumescent fireproof strip. -
Slitting saws for use with arbors TTLDTA and TTMGA6.35 When using this arbor TTMGA6.35 the screw head is only 1.5mm beyond the groover. The use of a bearing with 8 mm bore is possible on the shank side. These can be found in the bearings section through the main heading on the home page. TTLDTA Arbor inclusive spacers and bearing no. B16 (D = 16). Further bearings with bore 6,35 mm can be found in the bearings section through the main heading on the home page. -
SINKING AND STRIP RECESSING TCT For library and book shelving strip/tonk strip. -
Left Hand Counter Sink TCT Designed to fit metric boring bits with 10mm Shank. Suitable for 'V' point drills, Lip and Spur and most dowel drills. DESCRIPTION Designed to fit metric boring bits with 10mm Shank. Left Hand or Right Hand rotation. Suitable for 'V' point drills, Lip and Spur and most dowel drills. TTMBC4/10 for fixing onto the Shank section, for drill diameter 4-10mm. TTMBCF range for fixing directly onto the Flute section. -
The Titman Multi-Profiler Cutterhead is designed to take the popular WS 40m and 50mm cutter profiles. Using two location pins and a recessed locking flange, the Multi-Profiler is easily changed and secured, offering a whole range of standard and special profiles (specials on request). THIS IS FOR THE TOOL BODY ONLY. A large range of blades are available, download the catalogue pdf on our website, part codes TTFK000 to TTFK100 for blades and TTDK000 to TTDK100 for defectors. -
TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames -
TCT Undercut With Bearing A range of cutters used to produce a recess on the underside of lettering. DESCRIPTION A range of cutters used to produce a recess on the underside of lettering. -
RouterBorer These are a designed for use at a faster RPM than standard boring bits for recessing circular hinges. A template and a guide will ensure accurate hole placement on the workpiece and that the router itself is secure with no sideways movement DESCRIPTION The CB version have chip breakers for use on more fibrous materials. The design allows the tool to run at speeds of 1000-20,000 RPM. -
HINGE AND FIRE STRIP RECESSER TCT A cutter ideal for hinge recessing and the underside of handrails, these have extra long shanks for use with the popular hinge jigs on the market -
A unique cutter that will trim the top and bottom edges of a panel simultaneously, the centrally mounted bearing follows the profile. Tips are reversible and are sold in boxes of 10. -
TCT Profile Edge Mould This range of edge moulding offers a varied selection of profiles for table edgings
