-
TCT Double Flute For edging sinks and vanity bowls. The special taper on the Bearing sleeve allows for perfect guide following around the inside of the bowl. -
TCT Double Flute Helps to reduce the effect of overlay joint line. DESCRIPTION Sometimes called 'waterfall effect' giving a non-drip edge to a worktop. TTXC214 has a shorter cut length, ideal for use on 12.5mm thick material. TTXC216 is fitted with self-guided Bearing for use with 15mm thick material. TTXC221 is ideal for use on 19mm (3/4 inch) thick material. -
TCT Two Flute Box Cove For fine work to produce double radius in one pass, adjustable should material thicknesses vary. DESCRIPTION A further extension of the guttering cutter range with deeper cut for shallow fingerpull applications. Can also be used for cove cut on worktop upstands. For use with a template and guide bush for draining board grooves. Is suitable for producing grooves to take insulation rods. -
TCT Double Flute TTXC611 is the perfect cutter for panel raising work. TTXC616 is designed for large 45 degree chamfer work with guide Bearing. -
A particular advantage to this replacement tip style over the conventional brazed variety is that the diameter remains constant. These double and single flute style flush trim router cutters are designed for use on template and pattern work and can be used in hand-held and table-mounted routers. They have a shank mounted bearing which will run along and follow the template which is attached to the workpiece with the end result being an exact duplicate of the template itself. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
This range are ideal for use on wood, plywood, MDF and other wood composites, plastics, and solid surface materials. Widely used for copy profiling and flush trimming, the replaceable tip design provides a constant diameter and the flexibility of instant tip changes whilst onsite. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10. -
The cutters still give a fantastic finish, great longevity of use and of course can be re-sharpened, a superb cutter at a very competitive price. -
A range of rebate cutters bearing guided, bearings can be changed to a different diameter to produce various rebate depths. The TTRCB95-1/2RT and TTRCB95-8RT are fitted with the TT3/8-B37514 bearing and also come with the TT1/2-B127, TTB15 and TTB19 bearings. The TTRCb9512RT is fitted with 2 - TT1/2-B127 bearings and can then be used in conjunction with the TTRR range of aluminium sleeves to produce the various rebate depths. These rings are placed in the middle of the 2 bearings which then keep them secure whilst routing. If you take the diameter dimension of the cutter minus the diameter dimension of the ring and divide by 2 this will give you the rebate depth. Tips are reversible and are sold in boxes of 10 -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself. -
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work. -
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical -
TCT Bevelled With Bottom Bearing A range of bevelled chamfer cutters with bottom guide bearing for large sections of timber, chipboard and MDF. -
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility. -
DESCRIPTION Supplied with 2 bearings, 12.7mm and 16mm in diameter, two shapes can produced with one cutter by changing the bearing size. The 16 mm diameter bearing removes the bottom quirk. -
TCT Dovetail Standard sizes for all dovetail and sliding dovetail applications ie slot dovetail, hidden dovetail, etc. DESCRIPTION Available with scribers on TTDCS14.3-8 & TTDCS127-1/4 to enable use in conjunction with portable routing jigs. Parts TTADC12B-1/4, TTBDC14B-1/4 have shank mounted bearings fitted. -
TCT Undercut Groovers 4 Wing M12*1 Internal Bore Groovers 4 wing and threaded M12*1.5mm bore which enable flush recessing. The arbor and bearings are sold separately and the TTUGA arbor is for use without a bearing only, the others can be used with or without a bearing provided the correct shims are used to bring it flush at the bottom. Arbor and bearings are separate items. All prices exclude VAT. All prices exclude VAT. DESCRIPTION TTUG10, TTUG15 and TTUG20 groover can be used for fitting fire proof strip. If no bearing is used, you can use the arbor TTUGA. If bearing is to be used, use the arbors TTUGALR for all groovers except TTUG20, which requires Arbor TTUGAXLR. The following list shows the Rebate Depth obtainable with each Bearing size for a 50mm diameter groover: B25=12.5mm, B26=12mm, B28=11mm, B30=10mm, B32=9mm, B34=8mm, B36=7mm, B37=6.5mm, B42=4mm. -
TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip.
-
Profile Edge Mould Classic Lambs Tongue TCT Bearing Guided Classic Lambs Tongue mould perfect for finishing table and furniture tops. DESCRIPTION These cutters are supplied with a 9.5mm diameter bearing and a 12.7mm diameter bearing. -
Right Hand Drill TCT Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter. Drilling machines only - not for use on portables. DESCRIPTION Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter (see below). Drilling machines only - not for use on portables. All drills 20mm long. TTCSD8 (1/4 inch Shank) and TTCSD9.5 (10mm Shank): Countersink Diameter D=9.5mm (matches plug produced by TTPMC8), Drill Diameter d=4.8mm, No. 8 Wood Screw TTCSD10 (1/4 inch Shank) and TTCSD12 (10mm Shank): Countersink Diameter D=12mm (matches plug produced by TTPMC10), Drill Diameter d=5.5mm, No. 10 Wood Screw TTCSD12 (1/4 inch Shank) and TTCSD16 (10mm Shank): Countersink Diameter D=16mm (matches plug produced by TTPMC12), Drill Diameter d=6.35mm, No. 12 Wood Screw -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
Drill holder for Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. DESCRIPTION Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. Available with spigot if required. TTMB10M has a 10mm thread and suits Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen machines. TTAB10M has a 10mm thread and suits Alberti, SCM, Vitap, Balestrini, Bilek, Ombe machines. TTNM8M has a 8mm thread and suits Nottmeyer machines. TTMB10BR has a 3/8 BSF thread and suits Brookman machines: TTMB10RY has a 3/8 BSW thread and suits Rye machines: Please ensure correct variation is selected when ordering. For machines not listed here please contact the Sales Department with details of thread size and type, aperture size and overall lengths for advice. -
TCT Two Flute Rounding Over Fitted with a Shank mounted Bearing. First cut with TTXC301, finshing using matching TTXC321. Eliminates flat on edge. -
STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish. -
British made TCT Trade cutters for Aquamac and Intumescent Strips. Use E207HTC for Aquamac 21, E206HTC for Aquamac 63. -
British made Tungsten Carbide Tipped Dovetail cutters with differing angles and length of cut to produce accurate joints time and again for making furniture, drawers & boxes etc. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
Used to create a fluting effect on the edge of furniture. TTRWHC range are used to create a fluting effect on the edge of furniture. TTSBCB range has a removeable bearing system. When requiring a self guiding effect ensure the jig has clearance between workpiece and bottom of cutter. TTHHC20 and TTRHHC20 complement each other and when used together perform the cuts needed to form a drop leaf table joint. Please note some of these products are Made To Order. -
TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand
-
DESCRIPTION Made from solid tungsten carbide these are designed with a plunge facility for creating slots or channels for locks and drainage. -
DESCRIPTION These cutters are designed with a plunge facility for creating slots or channels for locks and drainage. The double flute makes them more suitable for non ferrous metals. -
HINGE AND FIRE STRIP RECESSER TCT A cutter ideal for hinge recessing and the underside of handrails, these have extra long shanks for use with the popular hinge jigs on the market -
TCT Profile Edge Mould This range of edge moulding offers a varied selection of profiles for table edgings
