-
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
Profile Edge Mould Classic Lambs Tongue TCT Bearing Guided Classic Lambs Tongue mould perfect for finishing table and furniture tops. DESCRIPTION These cutters are supplied with a 9.5mm diameter bearing and a 12.7mm diameter bearing. -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
TCT Corner Ovolo Profiles and moulds in one operation. Ideal for aperture cutting, ie snooker table pockets, worktops and cover mouldings. DESCRIPTION WCO Type have plunge facility. WCOB Type have bearing. -
Profile Edge Mould Classic Decor TCT Bearing Guided This classic shape is a fine cutter for reproduction furniture, bolection mould and any work in which the natural finish and beauty of wood is to be enhanced. -
TCT Classical Perfect for drawer fronts in solid material for enhancing the style and appearance of panelled work. -
TCT Adjustable Top and Bottom Chamfer with Bearing DESCRIPTION For bevelling and trimming the top and bottom edges of the workpiece. Adjust the four wing trimmer blocks with spacers for differing widths of material. Maximum material thickness 15mm for the DCB16 and is fixed Maximum material thickness 32mm, minimum material thickness 16mm for the BCS38. Maximum material thickness 36mm, minimum material thickness 19mm for the BGAC45. To extend the life of cutting edges use 26mm bearing. -
TCT Bevelled With Bottom Bearing A range of bevelled chamfer cutters with bottom guide bearing for large sections of timber, chipboard and MDF. -
BALL GROOVER SINGLE FLUTE TCT A range of single flute ball slot cutters designed for pipe and cable laying into timber and MDF. DESCRIPTION Important - cut neck slot first, do not run on neck but use a side fence or guide. NB The neck does not cut. Suggested cutters for neck slot: TTM716 for TTTSB127 neck diameter 6.5mm; TTM1020 for TTTSB254 neck diameter 9.5mm; TTM1325 for TTTSB32 neck diameter 12.7mm -
TCT Groovers Light Duty 4 wing Suitable for producing biscuit jointing slots, small T&G sections and rebates, can be used with or without a bearing and multiple groovers can be mounted on the one arbor. DESCRIPTION Use TTLDTANB Arbor when no Bearing is used. Use TTLDTA Arbor with TTB16 Bearing. Z=Number of flutes. RPM=Maximum revolutions per minute Groove Depth with various bearings are as follows TTB14 = 13.6mm, TTB15 = 13.1mm, TT5/8-B16 = 12.6mm, TTB17 = 12.1mm, TTB18 = 11.6mm, TTB19 = 12.1mm, TTB20 = 10.6mm, TTB21 = 10.1mm, TTB22 = 9.6mm, TTB23 = 9.1mm, TTB24 = 8.6mm, TTB25 = 8.1mm -
Slitting saws for use with arbors TTLDTA and TTMGA6.35 When using this arbor TTMGA6.35 the screw head is only 1.5mm beyond the groover. The use of a bearing with 8 mm bore is possible on the shank side. These can be found in the bearings section through the main heading on the home page. TTLDTA Arbor inclusive spacers and bearing no. B16 (D = 16). Further bearings with bore 6,35 mm can be found in the bearings section through the main heading on the home page. -
TCT Undercut With Bearing A range of cutters used to produce a recess on the underside of lettering. DESCRIPTION A range of cutters used to produce a recess on the underside of lettering. -
TCT Dovetail Standard sizes for all dovetail and sliding dovetail applications ie slot dovetail, hidden dovetail, etc. DESCRIPTION Available with scribers on TTDCS14.3-8 & TTDCS127-1/4 to enable use in conjunction with portable routing jigs. Parts TTADC12B-1/4, TTBDC14B-1/4 have shank mounted bearings fitted. -
DESCRIPTION Special relief on the cutter body allows for deep slotting work. Suitable for plunging. Note:LH58L, LH58L2, LH34L, not to be used in a portable router. -
TCT Biscuit Joint Biscuit Joint Slotter with Arbor self guided. Comes with 3 interchangeable bearings to produce slots for the popular biscuit sizes of 0,10 and 20. Ideal for hardwood, softwoods, ply, MDF and chipboard. DESCRIPTION Z=Number of flutes. RPM=Maximum revolutions per minute Groove Depth with various bearings are as follows TTB15 = 12.5mm, TTB19 = 10.5mm, TTB23 = 8.5mm. -
Barley Twist TCT A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Can also be used for edge profiling. DESCRIPTION A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Please also see the TTGC and the Ogee range for alternative cutters that may be used for fluting. TTBTC1 - Astragal Effect gives an extra feature to turned parts. Can also be used as an edge profile or special panel effect. TTBTC2 - This Shallow Radius cutter is very popular for standard barley twist design. Ideal for use on heavy duty lathes with routing attachment. TTBTC3 - This Ovolo Cutter is a deeper version of TTBTC2. Can be used for engraving when used with a CNC router machine. TTBTC4 - This Double Radius Effect cutter can be used as an edge mould cutter. TTBTC5 - The largest Ogee Effect cutter in this range. An ideal choice for flat roping or parallel fluting. TTBTC6 - The smaller version of the TTBTC5 Ogee Cutter. Can also be used for roping effect and fluting as well as panel raising. -
Used to create a fluting effect on the edge of furniture. TTRWHC range are used to create a fluting effect on the edge of furniture. TTSBCB range has a removeable bearing system. When requiring a self guiding effect ensure the jig has clearance between workpiece and bottom of cutter. TTHHC20 and TTRHHC20 complement each other and when used together perform the cuts needed to form a drop leaf table joint. Please note some of these products are Made To Order. -
This range of bead cutters produce mouldings to highlight features such as fascia rails, chair backs or decorative sections 'planted' on bedroom furniture to bring a line and feature to a continuous layout. TTDSB4 is a sunken flute cutter with a shallow radius to produce a soft effect. An ideal cutter to produce fluted pillars, for fire surrounds and 'gable ends' on bedroom furniture. Useful cutter to cut on a glue joint to hide the glue line. TTDSB5 is a sunk bead mould perfect for finishing wall unit facias and cover moulds on window sections. TTDSB7 is ideal for fluting or decorating solid surrounds. -
These cutters are the perfect solution to finishing cladding and corners on pillar covering or for enhancing square table legs or returns on wall unit furniture. The diameter of the bead is twice the value of the radius i.e. R=2mm the bead diameter is 4mm.
