-
DESCRIPTION 2 wing with or without centre point and with or without scribers, shanks are 10mm with flat on one side and end adjusting screw. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation. -
This range of single flute RT cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design in allows a perfect V in the bottom of the groove. The tips are reversible and sold in boxes of 10. -
Tips are reversible and are sold in boxes of 10. -
Angles are measured from the horizontal. Tips are reversible and are sold in boxes of 10. -
This range of single flute replacement tip cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. The TC tips are non reversible and are sold singularly. -
A range of rebate cutters bearing guided, bearings can be changed to a different diameter to produce various rebate depths. The TTRCB95-1/2RT and TTRCB95-8RT are fitted with the TT3/8-B37514 bearing and also come with the TT1/2-B127, TTB15 and TTB19 bearings. The TTRCb9512RT is fitted with 2 - TT1/2-B127 bearings and can then be used in conjunction with the TTRR range of aluminium sleeves to produce the various rebate depths. These rings are placed in the middle of the 2 bearings which then keep them secure whilst routing. If you take the diameter dimension of the cutter minus the diameter dimension of the ring and divide by 2 this will give you the rebate depth. Tips are reversible and are sold in boxes of 10 -
SPOILBOARD SURFACE PLANER 2 & 3 WING TCT For trimming aluminium flashing. DESCRIPTION TTSMC20 has a shear action for finer finish. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With either an up or downward cutting action the chipbreaker design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With either an up or downward cutting action the rougher / hogging design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action,, For use with CNC machines. -
SINGLE FLUTE SOLID CARBIDE UPCUT SPIRAL For use on plastics, acrylics, foam, ABS, ACP and light metals. DESCRIPTION These tools are designed to give a smooth finish on hard plastics. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With an up and downard cutting action on the one tool, the fluted compression style allows for fine finish on the top and bottom edges of the board. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
TCT Double Flute For bevelling inside bowl tops and similar applications. Avoids need to turn workpiece. -
Downturn Rebate Cutter Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. Lower illustration shows method of removing bowl from worktop. DESCRIPTION To produce a 13mm rebate for the downturns on solid surface worktops. Fitted with a plastic sleeved bearing TTPB127. -
These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself. -
STC Spiral The accepted solid carbide cutter for machining and routing acrylics, plastics and Perspex. The helical cut gives a much easier lead into the material preventing snatching and chipping on cut. DESCRIPTION Perfect preparation before flame polishing of Perspex. Downcut for chip-free finish on MFC. DC in product code denotes Downcut. * = For use on very fine acrylics where downward cutting action will prevent vibration and component lifting. Use a P.T.F.E. spray to enhance performance and prevent waste from welding to the tool. -
TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip. -
This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10. -
DESCRIPTION Ideal for veining work, freehand decor for panels and useful for character lining work on sign writing applications in solid timbers. The angle ( measurement A ) is measured from the horizontal. TTVGC45SF-1/2, TTVGC45SF-1/4, TTVGC45SF-12, TTVGC60SF-1/2, TTVGC60SF-1/4, TTVGC60SF-12, TTVGC60SF-8 cut to a point. TTVGCB45-1/4, TTVGCB60-127-1/4 have a shank mounted bearing. -
DESCRIPTION To achieve a perfect tongued and grooved joint for flooring and paneling use the TTFFC28 in conjunction with a TTG35552-6.35 mini groover ( for the groove ). The same arbor can be used for the TTFFC28 and TTFA20 The TTFA20 is also for use with the TTLDTA style of arbor. -
TCT Multi-Mould DESCRIPTION TTTOR25 gives an ornate moulding used in full or in part. TTTOR22 is a possible picture rail and cover mould cutter. TTTOR27 ideal to use the complete mould or part for short production runs. Excellent cutter to produce ornate skirting and architrave moulding. TTTOR-B gives a deep cavetto effect with a bead to break up the line of the mould. The fine lines of this cutter make it an excellent choice for matching skirting and architrave. TTTOR-C is a variation of the Torus Mould (TTTOR-T). -
TCT T-Slot Square Edged Designed for creating the T-slot in wall panels used in the point of sale industry for shelving and display purposes. -
Ideal for skimming on CNC routing machines. Tips are reversible and are sold in boxes of 10. -
TCT Stair Nosing This range have a flatter style to a standard full bull nose offering an alternative profile on stair treads, window boards and these can also be used to relieve sharp corners on the standard board thickness. DESCRIPTION The TTSNCB10 has a bottom bearing. -
TCT Bullnose Staff Bead A full bullnose radius for stair treads, nosings, window boards and edge mouldings Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
Twist Drills Slow Spiral for plastics, brass, chipboard and MDF DESCRIPTION The design of the slow spiral drills are better suited for use with the counterbore and countersink ranges as they help to prevent clogging. (over the faster helix versions.) -
UP/DOWN SHEAR STAGGERED TOOTH TCT A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. DESCRIPTION A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. -
SINGLE FLUTE SOLID CARBIDE For use on plastics, acrylics and light metals. The 'O' flute design reduces heat build up on low melting point materials. DESCRIPTION These straight single fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam, ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish and use the shortest cut lengths possible. The radius flute design gives effective cutting on ductile plastics, an ideal tool for cutting ABS components for example on 5 and 7 axis machines and offer efficient effective chip clearance with the for smooth feed rate that CNC's offer -
Countersink Shankless SS For Pillar drilling machines only, not on portables. -
TCT Machine Countersink & Bores A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
Shankless Counterbore For Pillar drilling machines only, not on portables. DESCRIPTION For Pillar drilling machines only, not on portables. Drills and Allen Keys not included. Available in TCT (part codes suffixed TCT) and Silver Steel (part codes suffixed SS) and to suit a selection of drill hole diameters. Please ensure correct variation is selected when ordering. -
Left Hand TCT A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
A range of Grecian and Roman Ovolo Effect cutters, essential for faithful matching of Georgian window repair or production. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section. -
DESCRIPTION -
DESCRIPTION Supplied with 2 bearings, 12.7mm and 16mm in diameter, two shapes can produced with one cutter by changing the bearing size. The 16 mm diameter bearing removes the bottom quirk. -
Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings. -
REBATER WITH REPLACEMENT TC TIPS Replacement Tip Rebate 4 Wing With Bearing DESCRIPTION Replacement Tip Rebate 4 Wing With Bearing Z=Number of flutes. RPM=Maximum revolutions per minute -
DESCRIPTION A comprehensive range of Core Box, Cove, Radius, Guttering cutters with radii from 1.6mm to 25.4mm. Cutters with part number starting TTCBB have a shank mounted bearing fitted. -
CT Plug Making Drilling machines only. DESCRIPTION Drilling machines only. Can be used with the CSD range of Countersink Drills and CBD range of Counterbore Drills. Maximum Plug Depth=16mm for all cutters. TTPMC8 Plug Diameter=9.5mm, No. 8 Wood Screw TTPMC9 Plug Diameter=10mm TTPMC10 Plug Diameter=12mm, No. 10 Wood Screw TTPMC127 Plug Diameter=12.7mm TTPMC12 Plug Diameter=16mm, No. 12 Wood Screw -
TCT Tapered Plug Making Plug making cutter producing a tapered plug to be driven in and tightly secured. To avoid cutter deflection use this TTTPC range of cutters only on Pillar Drilling machines and do not exceed 3,000 RPM. Feed evenly into material. DESCRIPTION Plug making cutter producing a tapered plug to be driven in and tightly secured. To avoid cutter deflection use this TTTPC range of cutters only on Pillar Drilling machines and do not exceed 3,000 RPM. Feed evenly into material. -
TCT Minature Bead Cutters A range of minature beading cutters for fine decorative work. These cutters perform best at 24,000 RPM. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
Pin diameter is 5.5mm by 5.5mm long -
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility. -
Right Hand Drill TCT Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter. Drilling machines only - not for use on portables. DESCRIPTION Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter (see below). Drilling machines only - not for use on portables. All drills 20mm long. TTCSD8 (1/4 inch Shank) and TTCSD9.5 (10mm Shank): Countersink Diameter D=9.5mm (matches plug produced by TTPMC8), Drill Diameter d=4.8mm, No. 8 Wood Screw TTCSD10 (1/4 inch Shank) and TTCSD12 (10mm Shank): Countersink Diameter D=12mm (matches plug produced by TTPMC10), Drill Diameter d=5.5mm, No. 10 Wood Screw TTCSD12 (1/4 inch Shank) and TTCSD16 (10mm Shank): Countersink Diameter D=16mm (matches plug produced by TTPMC12), Drill Diameter d=6.35mm, No. 12 Wood Screw -
TCT Ogee Used for paneling and edge moulding for that classic ogee feature. -
TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes. -
MIDDLE BEARING GUIDED TOP & BOTTOM FLUSH TRIM 90 DEG TCT & RT This double flute cutter trims the top and bottom edges simultaneously as bearing follows the profile in the centre of the material. These industrial quality premium grade tungsten carbide flush trimmers are ideal for wood, plywood, MDF and other wood composites, plastics, and solid surface materials DESCRIPTION Unique in that this cutter will trim the top and bottom edges of a panel simultaneously, whilst the centrally mounted bearing follows the profile. -
A range of lip and spur drills with 10mm diameter parallel shanks. Available with right hand rotation. -
A range lip and spur drills with 8mm diameter parallel shanks that have an end adjusting ting screw. Available with right hand or left hand rotation. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
TCT Raised Panel Grecian Ogee Ideal for heavy cornice and dado rail production. Used in restoration and as a classic mould for picture frames, to produce raised panels on drawer fronts and doors. -
Profile Edge Mould Classic Lambs Tongue TCT Bearing Guided Classic Lambs Tongue mould perfect for finishing table and furniture tops. DESCRIPTION These cutters are supplied with a 9.5mm diameter bearing and a 12.7mm diameter bearing. -
CT Finger Pull Grip Square Bottom For solid handles and pulls on kitchen and wall unit doors, the perfect solutions for providing positive grips and softened, easy-on-the-fingers edges without the need for external hardware. DESCRIPTION TTFPC22 is a variation of TTFPC19 giving a square bottom and undercut. Both of these have a centre tip for plunging -
A range drills with a 1mm long 45 degree chamfer on the tip edge for use in the specialized boring machine MAFELL DuoDübler . Shanks are 8mm diameter with a flat on one side and length adjusting screw in the end. Available with right hand. -
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
Ffor the popular sizes of stair treads for use in conjunction with CNC and trenching machines, cutters are offered in both left and right hand rotation. Tips are reversible and are sold in boxes of 10
-
These cutter are double flute and they are non plunging with an outside fixing style for the use of profiling, the tips have 4 cutting edges so they can also be ramped down into workpiece. Tips are reversible and are sold in boxes of 10 -
STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish. -
TAPERED DOUBLE FLUTE TCT Two flute cutters with taper designed for constructing vacuum forming moulds. DESCRIPTION Two flute cutters with taper designed for constructing vacuum forming moulds. 2 degree tapered side allows easier release. TTH58212T can produce a leading edge on a door. -
DOWNCUT SHEAR DOUBLE FLUTE TCT Shear action downcut to reduce breakout. DESCRIPTION For short producton runs only. For longer and improved performance see our Solid Carbide Range. *These tools are designed to give a 'tear' free groove in conjunction with a tight housed joint when using plywood.
-
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work. -
Left Hand Rotation 3 Wing With 3 Scribers and Centre Point A comprehensive range of hinge borers. Please ensure correct variation is selected when ordering. DESCRIPTION A comprehensive range of hinge borers. All are available in 57mm overall lengths. Some 2 wing with 2 scribers cutters are also available in 70mm and 77mm overall lengths. All have 10mm diameter Left Hand or Right Hand Shanks. Shanks have flat on one side and length adjusting screw. Some sizes are also available with or without centre point. The TTTMB range have a removable/replaceable centre point with a 'V' point effect at one end, flush finish at the other end. Please ensure correct variation is selected when ordering. For use on Multi-Boring machines. -
DESCRIPTION 2 wing with centre point and with or without scribers and parallel shanks. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
2 Wing with C/Point without Scribers TCT 2 wing available with or without scribers and parallel shanks. DESCRIPTION 2 wing available with or without scribers and parallel shanks. Right hand with centre point. Left hand available to special order - please contact the Sales Department for details. For boring bits at above 80mm overall length please contact the Sales Department for pricing and availability. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Select correct boring bit design for machine, material and thickness: Drill or Boring Machines: Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM.
-
TCT Cove Mould Bearing Guided Producing a quarter round on the edge of the workpiece these are ideal for detailing casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables. DESCRIPTION These cutters come complete with TTB127 and TTB16 bearings. Matching rounding over cutters available for rule joints. -
TCT Corner Ovolo Profiles and moulds in one operation. Ideal for aperture cutting, ie snooker table pockets, worktops and cover mouldings. DESCRIPTION WCO Type have plunge facility. WCOB Type have bearing. -
Profile Edge Mould Classic Decor TCT Bearing Guided This classic shape is a fine cutter for reproduction furniture, bolection mould and any work in which the natural finish and beauty of wood is to be enhanced. -
TCT Chamfering Edge Chamfering Edge Cutters. Reducing and Chamfering. DESCRIPTION TTCEC45, TTCECR45, TTLTC4, TTLTCR4, TTLTC63, TTLTCR63 are non plunge but with bottom cut facility. TTCECR45 is the reverse of TTCEC45. TTCECR45L is the reverse of TTCEC45L. TTLTC4 and TTLTCR4 give a lambs tongue effect as TTROB range. TTLTCR4 is the reverse of TTLTC4. TTLTCR63 is the reverse of TTLTC63. -
TCT Classical Perfect for drawer fronts in solid material for enhancing the style and appearance of panelled work. -
TCT Adjustable Top and Bottom Chamfer with Bearing DESCRIPTION For bevelling and trimming the top and bottom edges of the workpiece. Adjust the four wing trimmer blocks with spacers for differing widths of material. Maximum material thickness 15mm for the DCB16 and is fixed Maximum material thickness 32mm, minimum material thickness 16mm for the BCS38. Maximum material thickness 36mm, minimum material thickness 19mm for the BGAC45. To extend the life of cutting edges use 26mm bearing. -
TCT Bevelled With Bottom Radius A range of bevelled cutters with a bottom radius ideal for scallop fluting and finger pull applications.
-
TCT Bevelled With Bottom Bearing A range of bevelled chamfer cutters with bottom guide bearing for large sections of timber, chipboard and MDF. -
This tool does not plunge. Tips are reversible and are sold in boxes of 10 -
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical -
This range are ideal for use on wood, plywood, MDF and other wood composites, plastics, and solid surface materials. Widely used for copy profiling and flush trimming, the replaceable tip design provides a constant diameter and the flexibility of instant tip changes whilst onsite. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
Universal Drill Adaptor suits 2mm diameter drill These Universal Drill Adaptors have a 10mm Shank with a flat on one side and the drill is secured with a grub screw.. DESCRIPTION These Universal Drill Adaptors have a 10mm Shank with a flat on one side and the drill is secured with a grub screw. -
Drill holder for Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. DESCRIPTION Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. Available with spigot if required. TTMB10M has a 10mm thread and suits Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen machines. TTAB10M has a 10mm thread and suits Alberti, SCM, Vitap, Balestrini, Bilek, Ombe machines. TTNM8M has a 8mm thread and suits Nottmeyer machines. TTMB10BR has a 3/8 BSF thread and suits Brookman machines: TTMB10RY has a 3/8 BSW thread and suits Rye machines: Please ensure correct variation is selected when ordering. For machines not listed here please contact the Sales Department with details of thread size and type, aperture size and overall lengths for advice. -
A particular advantage to this replacement tip style over the conventional brazed variety is that the diameter remains constant. These double and single flute style flush trim router cutters are designed for use on template and pattern work and can be used in hand-held and table-mounted routers. They have a shank mounted bearing which will run along and follow the template which is attached to the workpiece with the end result being an exact duplicate of the template itself. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand -
Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006
-
TCT Slotting Ideal for slots in pencil box lids etc and internal slotting work. Suitable for intumescent fireproof strip. -
SINKING AND STRIP RECESSING TCT For library and book shelving strip/tonk strip. -
Left Hand Counter Sink TCT Designed to fit metric boring bits with 10mm Shank. Suitable for 'V' point drills, Lip and Spur and most dowel drills. DESCRIPTION Designed to fit metric boring bits with 10mm Shank. Left Hand or Right Hand rotation. Suitable for 'V' point drills, Lip and Spur and most dowel drills. TTMBC4/10 for fixing onto the Shank section, for drill diameter 4-10mm. TTMBCF range for fixing directly onto the Flute section. -
The Titman Multi-Profiler Cutterhead is designed to take the popular WS 40m and 50mm cutter profiles. Using two location pins and a recessed locking flange, the Multi-Profiler is easily changed and secured, offering a whole range of standard and special profiles (specials on request). THIS IS FOR THE TOOL BODY ONLY. A large range of blades are available, download the catalogue pdf on our website, part codes TTFK000 to TTFK100 for blades and TTDK000 to TTDK100 for defectors. -
TCT Undercut With Bearing A range of cutters used to produce a recess on the underside of lettering. DESCRIPTION A range of cutters used to produce a recess on the underside of lettering.
