-
Angles are measured from the horizontal. Tips are reversible and are sold in boxes of 10. -
SPOILBOARD SURFACE PLANER 2 & 3 WING TCT For trimming aluminium flashing. DESCRIPTION TTSMC20 has a shear action for finer finish. -
SINGLE FLUTE SOLID CARBIDE UPCUT SPIRAL For use on plastics, acrylics, foam, ABS, ACP and light metals. DESCRIPTION These tools are designed to give a smooth finish on hard plastics. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself. -
STC Spiral The accepted solid carbide cutter for machining and routing acrylics, plastics and Perspex. The helical cut gives a much easier lead into the material preventing snatching and chipping on cut. DESCRIPTION Perfect preparation before flame polishing of Perspex. Downcut for chip-free finish on MFC. DC in product code denotes Downcut. * = For use on very fine acrylics where downward cutting action will prevent vibration and component lifting. Use a P.T.F.E. spray to enhance performance and prevent waste from welding to the tool. -
Weatherstrip Cutters A range of cutters designed to make the fitting of weatherstrip to door and window frames quick and easy. -
TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip. -
DESCRIPTION Ideal for veining work, freehand decor for panels and useful for character lining work on sign writing applications in solid timbers. The angle ( measurement A ) is measured from the horizontal. TTVGC45SF-1/2, TTVGC45SF-1/4, TTVGC45SF-12, TTVGC60SF-1/2, TTVGC60SF-1/4, TTVGC60SF-12, TTVGC60SF-8 cut to a point. TTVGCB45-1/4, TTVGCB60-127-1/4 have a shank mounted bearing. -
TCT Bullnose Staff Bead A full bullnose radius for stair treads, nosings, window boards and edge mouldings Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. -
SINGLE FLUTE SOLID CARBIDE For use on plastics, acrylics and light metals. The 'O' flute design reduces heat build up on low melting point materials. DESCRIPTION These straight single fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam, ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish and use the shortest cut lengths possible. The radius flute design gives effective cutting on ductile plastics, an ideal tool for cutting ABS components for example on 5 and 7 axis machines and offer efficient effective chip clearance with the for smooth feed rate that CNC's offer -
Left Hand TCT A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
A range of Grecian and Roman Ovolo Effect cutters, essential for faithful matching of Georgian window repair or production. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section. -
DESCRIPTION Supplied with 2 bearings, 12.7mm and 16mm in diameter, two shapes can produced with one cutter by changing the bearing size. The 16 mm diameter bearing removes the bottom quirk. -
Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings. -
REBATER WITH REPLACEMENT TC TIPS Replacement Tip Rebate 4 Wing With Bearing DESCRIPTION Replacement Tip Rebate 4 Wing With Bearing Z=Number of flutes. RPM=Maximum revolutions per minute -
Radiused 'V' Grooving TCT Ideal for panel and veining work, lettering, engraving, sign making, fluting, decorative trimming and barley twist. DESCRIPTION These do not cut to a point and will leave a 1mm - 2mm flat at the bottom of the groove. -
DESCRIPTION A comprehensive range of Core Box, Cove, Radius, Guttering cutters with radii from 1.6mm to 25.4mm. Cutters with part number starting TTCBB have a shank mounted bearing fitted. -
CT Plug Making Drilling machines only. DESCRIPTION Drilling machines only. Can be used with the CSD range of Countersink Drills and CBD range of Counterbore Drills. Maximum Plug Depth=16mm for all cutters. TTPMC8 Plug Diameter=9.5mm, No. 8 Wood Screw TTPMC9 Plug Diameter=10mm TTPMC10 Plug Diameter=12mm, No. 10 Wood Screw TTPMC127 Plug Diameter=12.7mm TTPMC12 Plug Diameter=16mm, No. 12 Wood Screw -
TCT Minature Bead Cutters A range of minature beading cutters for fine decorative work. These cutters perform best at 24,000 RPM. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
Pin diameter is 5.5mm by 5.5mm long -
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility. -
Right Hand Drill TCT Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter. Drilling machines only - not for use on portables. DESCRIPTION Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter (see below). Drilling machines only - not for use on portables. All drills 20mm long. TTCSD8 (1/4 inch Shank) and TTCSD9.5 (10mm Shank): Countersink Diameter D=9.5mm (matches plug produced by TTPMC8), Drill Diameter d=4.8mm, No. 8 Wood Screw TTCSD10 (1/4 inch Shank) and TTCSD12 (10mm Shank): Countersink Diameter D=12mm (matches plug produced by TTPMC10), Drill Diameter d=5.5mm, No. 10 Wood Screw TTCSD12 (1/4 inch Shank) and TTCSD16 (10mm Shank): Countersink Diameter D=16mm (matches plug produced by TTPMC12), Drill Diameter d=6.35mm, No. 12 Wood Screw -
TCT Ogee Used for paneling and edge moulding for that classic ogee feature. -
TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes. -
MIDDLE BEARING GUIDED TOP & BOTTOM FLUSH TRIM 90 DEG TCT & RT This double flute cutter trims the top and bottom edges simultaneously as bearing follows the profile in the centre of the material. These industrial quality premium grade tungsten carbide flush trimmers are ideal for wood, plywood, MDF and other wood composites, plastics, and solid surface materials DESCRIPTION Unique in that this cutter will trim the top and bottom edges of a panel simultaneously, whilst the centrally mounted bearing follows the profile. -
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish. -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work. -
DESCRIPTION 2 wing with centre point and with or without scribers and parallel shanks. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM.
