-
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
TCT Double Flute Fitted with self-guiding Bearing for rounding over. See cutters TTXC301 and TTXC321 for complete rounding over. -
TCT Two Flute Bowl Aperture Trimmer Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. DESCRIPTION Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
SINKING AND STRIP RECESSING TCT For library and book shelving strip/tonk strip. -
UP/DOWN SHEAR STAGGERED TOOTH TCT A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. DESCRIPTION A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
TCT Ogee Used for paneling and edge moulding for that classic ogee feature. -
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
DOWNCUT SHEAR DOUBLE FLUTE TCT Shear action downcut to reduce breakout. DESCRIPTION For short producton runs only. For longer and improved performance see our Solid Carbide Range. *These tools are designed to give a 'tear' free groove in conjunction with a tight housed joint when using plywood. -
Profile Edge Mould Decorative TCT The TTDEC range of tools are perfect for enhancing the appearance of square edged timber many of which offer balanced moulds for use on sections of woodwork at the centre of the design. -
British made TCT Cove Cutters with two flutes for a cleaner finish. Ideal for making radiused grooves for decorative finishes etc. When making deeper channels take several passes. -
Angles are measured from the horizontal. Tips are reversible and are sold in boxes of 10. -
TCT Double Flute For creating a 'step down' shadow line between bowl and sheet. -
TCT Double Flute Great care should be exercised when using this cutter to avoid 'cutter wander'. Use correct jig, template or side fence. Use a guide bush in conjunction with an offset template. -
TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section. -
TCT Minature Bead Cutters A range of minature beading cutters for fine decorative work. These cutters perform best at 24,000 RPM. -
TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes. -
TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
A unique cutter that will trim the top and bottom edges of a panel simultaneously, the centrally mounted bearing follows the profile. Tips are reversible and are sold in boxes of 10. -
TCT Two Flute Ventilation Slot Slots and produces a radius on the upper edge in one pass. -
TCT Two Flute Adjustable Double Radius Use with 1/2 inch thick material produces double radius in one pass. -
Weatherstrip Cutters A range of cutters designed to make the fitting of weatherstrip to door and window frames quick and easy. -
TCT Capillary Water Channel Groove All cutters in this range are non plunging but with bottom cutting action. DESCRIPTION This is designed to place a capillary groove on sill sections when used on site in a portable machine. -
DESCRIPTION To achieve a perfect tongued and grooved joint for flooring and paneling use the TTFFC28 in conjunction with a TTG35552-6.35 mini groover ( for the groove ). The same arbor can be used for the TTFFC28 and TTFA20 The TTFA20 is also for use with the TTLDTA style of arbor. -
TCT Stair Nosing This range have a flatter style to a standard full bull nose offering an alternative profile on stair treads, window boards and these can also be used to relieve sharp corners on the standard board thickness. DESCRIPTION The TTSNCB10 has a bottom bearing. -
Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006 -
Pin diameter is 5.5mm by 5.5mm long
-
These cutter are double flute and they are non plunging with an outside fixing style for the use of profiling, the tips have 4 cutting edges so they can also be ramped down into workpiece. Tips are reversible and are sold in boxes of 10 -
STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish.
