-
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
TCT Ogee Used for paneling and edge moulding for that classic ogee feature. -
DESCRIPTION 2 wing with centre point and with or without scribers and parallel shanks. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes. -
A range of lip and spur drills with 10mm diameter parallel shanks. Available with right hand rotation. -
TCT Undercut With Bearing A range of cutters used to produce a recess on the underside of lettering. DESCRIPTION A range of cutters used to produce a recess on the underside of lettering. -
British made bearing guided chamfers with TCT tips for clean accurate cutting and fast clearance of waste materials. -
British made bearing chamfers with 2 TCT tips for clean accurate cutting and fast clearance of waste materials. -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
TCT Classical Perfect for drawer fronts in solid material for enhancing the style and appearance of panelled work. -
TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip. -
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
TCT Bullnose Staff Bead A full bullnose radius for stair treads, nosings, window boards and edge mouldings Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. -
TCT T-Slot Square Edged Designed for creating the T-slot in wall panels used in the point of sale industry for shelving and display purposes. -
TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames -
Radiused 'V' Grooving TCT Ideal for panel and veining work, lettering, engraving, sign making, fluting, decorative trimming and barley twist. DESCRIPTION These do not cut to a point and will leave a 1mm - 2mm flat at the bottom of the groove. -
British made two flute TCT bottom single or double bearing guided flush trimming cutters. Gives a superb clear finish on timber , veneers and plastic laminate. The bottom bearing is for following an edge to give a superb finish to laminates and veneers. -
Ffor the popular sizes of stair treads for use in conjunction with CNC and trenching machines, cutters are offered in both left and right hand rotation. Tips are reversible and are sold in boxes of 10 -
MIDDLE BEARING GUIDED TOP & BOTTOM FLUSH TRIM 90 DEG TCT & RT This double flute cutter trims the top and bottom edges simultaneously as bearing follows the profile in the centre of the material. These industrial quality premium grade tungsten carbide flush trimmers are ideal for wood, plywood, MDF and other wood composites, plastics, and solid surface materials DESCRIPTION Unique in that this cutter will trim the top and bottom edges of a panel simultaneously, whilst the centrally mounted bearing follows the profile. -
STC 'Nib' Engraving Specially developed for engraving house names, bench plaques and other memorial inscriptions. The STC three flute 60 degree engraver is an ideal cutter for long production engraving work. -
With either an up or downward cutting action the rougher / hogging design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action,, For use with CNC machines. -
With either an up or downward cutting action the chipbreaker design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
With an up and downard cutting action on the one tool, the fluted compression style allows for fine finish on the top and bottom edges of the board. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines. -
British made two flute TCT top bearing guided profile flush trimming cutters. Gives a superb clean finish on timber, veneers and plastic laminate. The top bearing is for following a pattern or template to give a superb finish when replicating components. -
Tapered Repair Cutter Designed specifically to repair small imperfections in solid surface material. -
TCT Adjustable Top and Bottom Chamfer with Bearing DESCRIPTION For bevelling and trimming the top and bottom edges of the workpiece. Adjust the four wing trimmer blocks with spacers for differing widths of material. Maximum material thickness 15mm for the DCB16 and is fixed Maximum material thickness 32mm, minimum material thickness 16mm for the BCS38. Maximum material thickness 36mm, minimum material thickness 19mm for the BGAC45. To extend the life of cutting edges use 26mm bearing. -
TCT Dovetail Standard sizes for all dovetail and sliding dovetail applications ie slot dovetail, hidden dovetail, etc. DESCRIPTION Available with scribers on TTDCS14.3-8 & TTDCS127-1/4 to enable use in conjunction with portable routing jigs. Parts TTADC12B-1/4, TTBDC14B-1/4 have shank mounted bearings fitted. -
BALL GROOVER SINGLE FLUTE TCT A range of single flute ball slot cutters designed for pipe and cable laying into timber and MDF. DESCRIPTION Important - cut neck slot first, do not run on neck but use a side fence or guide. NB The neck does not cut. Suggested cutters for neck slot: TTM716 for TTTSB127 neck diameter 6.5mm; TTM1020 for TTTSB254 neck diameter 9.5mm; TTM1325 for TTTSB32 neck diameter 12.7mm -
CT Finger Pull Grip Square Bottom For solid handles and pulls on kitchen and wall unit doors, the perfect solutions for providing positive grips and softened, easy-on-the-fingers edges without the need for external hardware. DESCRIPTION TTFPC22 is a variation of TTFPC19 giving a square bottom and undercut. Both of these have a centre tip for plunging
