24000

  • Burrs and Rasps STC

    £16.83£133.04
    Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Weatherseal Seal TCT

    £33.64£61.17
    Weatherstrip Cutters A range of cutters designed to make the fitting of weatherstrip to door and window frames quick and easy.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Sash Bar TCT

    £74.94£133.04
    A range of Grecian and Roman Ovolo Effect cutters, essential for faithful matching of Georgian window repair or production.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DESCRIPTION To achieve a perfect tongued and grooved joint for flooring and paneling use the TTFFC28 in conjunction with a TTG35552-6.35 mini groover ( for the groove ). The same arbor can be used for the TTFFC28 and TTFA20 The TTFA20 is also for use with the TTLDTA style of arbor.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Capillary Water Channel Groove All cutters in this range are non plunging but with bottom cutting action. DESCRIPTION This is designed to place a capillary groove on sill sections when used on site in a portable machine.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Ventilation Slot TCT

    £79.51£87.17
    TCT Two Flute Ventilation Slot Slots and produces a radius on the upper edge in one pass.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Raised Panel TCT

    £61.05£163.62
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Pin diameter is 5.5mm by 5.5mm long
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • UP/DOWN SHEAR STAGGERED TOOTH TCT A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. DESCRIPTION A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Edge Mould TCT

    £79.92£149.86
    TCT Profile Edge Mould This range of edge moulding offers a varied selection of profiles for table edgings
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TAPERED DOUBLE FLUTE TCT Two flute cutters with taper designed for constructing vacuum forming moulds. DESCRIPTION Two flute cutters with taper designed for constructing vacuum forming moulds. 2 degree tapered side allows easier release. TTH58212T can produce a leading edge on a door.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Decorative Edge

    £60.25£102.45
    Profile Edge Mould Decorative TCT The TTDEC range of tools are perfect for enhancing the appearance of square edged timber many of which offer balanced moulds for use on sections of woodwork at the centre of the design.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Hinge Recessor

    £32.11£36.70
    HINGE AND FIRE STRIP RECESSER TCT A cutter ideal for hinge recessing and the underside of handrails, these have extra long shanks for use with the popular hinge jigs on the market
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • SINGLE FLUTE SOLID CARBIDE For use on plastics, acrylics and light metals. The 'O' flute design reduces heat build up on low melting point materials. DESCRIPTION These straight single fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam, ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish and use the shortest cut lengths possible. The radius flute design gives effective cutting on ductile plastics, an ideal tool for cutting ABS components for example on 5 and 7 axis machines and offer efficient effective chip clearance with the for smooth feed rate that CNC's offer
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Sunk Bead Decorative TCT

    £93.28£96.34
    This range of bead cutters produce mouldings to highlight features such as fascia rails, chair backs or decorative sections 'planted' on bedroom furniture to bring a line and feature to a continuous layout. TTDSB4 is a sunken flute cutter with a shallow radius to produce a soft effect. An ideal cutter to produce fluted pillars, for fire surrounds and 'gable ends' on bedroom furniture. Useful cutter to cut on a glue joint to hide the glue line. TTDSB5 is a sunk bead mould perfect for finishing wall unit facias and cover moulds on window sections. TTDSB7 is ideal for fluting or decorating solid surrounds.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Two Flute Adjustable Double Radius Use with 1/2 inch thick material produces double radius in one pass.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • SPOILBOARD SURFACE PLANER 2 & 3 WING TCT For trimming aluminium flashing. DESCRIPTION TTSMC20 has a shear action for finer finish.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Select options This product has multiple variants. The options may be chosen on the product page Details
  • Stair Housing TCT

    £64.23£84.11
    TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Stair Nosing TCT

    £61.48£104.51
    TCT Stair Nosing This range have a flatter style to a standard full bull nose offering an alternative profile on stair treads, window boards and these can also be used to relieve sharp corners on the standard board thickness. DESCRIPTION The TTSNCB10 has a bottom bearing.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Sunk Bead Bearing Guided TCT

    £84.11£113.17
    Used to create a fluting effect on the edge of furniture. TTRWHC range are used to create a fluting effect on the edge of furniture. TTSBCB range has a removeable bearing system. When requiring a self guiding effect ensure the jig has clearance between workpiece and bottom of cutter. TTHHC20 and TTRHHC20 complement each other and when used together perform the cuts needed to form a drop leaf table joint. Please note some of these products are Made To Order.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DOWNCUT SHEAR DOUBLE FLUTE TCT Shear action downcut to reduce breakout. DESCRIPTION For short producton runs only. For longer and improved performance see our Solid Carbide Range. *These tools are designed to give a 'tear' free groove in conjunction with a tight housed joint when using plywood.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Sinking & Strip Recessor

    £71.87£79.69
    SINKING AND STRIP RECESSING TCT For library and book shelving strip/tonk strip.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • STC Spiral The accepted solid carbide cutter for machining and routing acrylics, plastics and Perspex. The helical cut gives a much easier lead into the material preventing snatching and chipping on cut. DESCRIPTION Perfect preparation before flame polishing of Perspex. Downcut for chip-free finish on MFC. DC in product code denotes Downcut. * = For use on very fine acrylics where downward cutting action will prevent vibration and component lifting. Use a P.T.F.E. spray to enhance performance and prevent waste from welding to the tool.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • SINGLE FLUTE SOLID CARBIDE UPCUT SPIRAL For use on plastics, acrylics, foam, ABS, ACP and light metals. DESCRIPTION These tools are designed to give a smooth finish on hard plastics.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Rebate Bearing Guided TCT

    £45.00£47.00
    British made two flute TCT bottom bearing guided rebate cutters & stepped rebate cutter. These rebate cutters can be used for manufacturing rebates, rebated corners, lap joints, tongues etc. When a full rebate is required make two passes.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • British made TCT self guided corner bead cutter with two flutes for a cleaner finish. Ideal for making beautifull edge moulds for decorative finishes etc. Full corner beads can be made by making a second pass at 90 degrees.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  •   DESCRIPTION  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Rounding Over Pin Guided TCT

    £53.52£88.70
    TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Radius Cove TCT

    £22.00£40.00
    British made TCT Cove Cutters with two flutes for a cleaner finish. Ideal for making radiused grooves for decorative finishes etc. When making deeper channels take several passes.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Drill holder for Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. DESCRIPTION Available in different thread sizes and in Right Hand (part codes suffixed RH) and Left Hand (part codes suffixed LH) threads to suit a variety of popular machines. Available with spigot if required. TTMB10M has a 10mm thread and suits Morbidelli, Biesse, Weeke, Reimall, Torwegge, Busellato, Bottcher, Gessner, Ayen machines. TTAB10M has a 10mm thread and suits Alberti, SCM, Vitap, Balestrini, Bilek, Ombe machines. TTNM8M has a 8mm thread and suits Nottmeyer machines. TTMB10BR has a 3/8 BSF thread and suits Brookman machines: TTMB10RY has a 3/8 BSW thread and suits Rye machines: Please ensure correct variation is selected when ordering. For machines not listed here please contact the Sales Department with details of thread size and type, aperture size and overall lengths for advice.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Panel Moulding TCT

    £38.23£71.87
    TCT Minature Bead Cutters A range of minature beading cutters for fine decorative work. These cutters perform best at 24,000 RPM.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Ogee TCT

    £38.23£108.58
    TCT Ogee Used for paneling and edge moulding for that classic ogee feature.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DESCRIPTION 2 wing with  centre point and with or without scribers and parallel shanks. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • A range of lip and spur drills with 10mm diameter parallel shanks. Available with right hand rotation.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Undercut With Bearing A range of cutters used to produce a recess on the underside of lettering. DESCRIPTION A range of cutters used to produce a recess on the underside of lettering.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Select options This product has multiple variants. The options may be chosen on the product page Details
  • Chamfer Bearing Guided TCT

    £21.00£42.00
    British made bearing guided chamfers with TCT tips for clean accurate cutting and fast clearance of waste materials.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • V Groover and chamfer TCT

    £22.00£40.00
    British made bearing chamfers with 2 TCT tips for clean accurate cutting and fast clearance of waste materials.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Folding Tool TCT

    £50.47£55.58
    ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Classic Cove TCT

    £67.28£96.34
    TCT Classical Perfect for drawer fronts in solid material for enhancing the style and appearance of panelled work.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Fire Strip Slotter TCT

    £61.97£114.70
    TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Hand Bead TCT

    £88.70£142.22
    TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Edge Bead Heavy Duty TCT

    £97.88£110.10
    TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Bullnose Staff Bead A full bullnose radius for stair treads, nosings, window boards and edge mouldings Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • T Slot TCT & PCD

    £50.47£300.00
    TCT T-Slot Square Edged Designed for creating the T-slot in wall panels used in the point of sale industry for shelving and display purposes.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Keyhole Slot TCT

    £44.36£50.47
    TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • V Grooving Radiused TCT

    £55.06£70.35
    Radiused 'V' Grooving TCT Ideal for panel and veining work, lettering, engraving, sign making, fluting, decorative trimming and barley twist. DESCRIPTION These do not cut to a point and will leave a 1mm - 2mm flat at the bottom of the groove.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • British made two flute TCT bottom single or double bearing guided flush trimming cutters. Gives a superb clear finish on timber , veneers and plastic laminate. The bottom bearing is for following an edge to give a superb finish to laminates and veneers.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Ffor the popular sizes of stair treads for use in conjunction with CNC and trenching machines, cutters are offered in both left and right hand rotation. Tips are reversible and are sold in boxes of 10
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • MIDDLE BEARING GUIDED TOP & BOTTOM FLUSH TRIM 90 DEG TCT & RT This double flute cutter trims the top and bottom edges simultaneously as bearing follows the profile in the centre of the material. These industrial quality premium grade tungsten carbide flush trimmers are ideal for wood, plywood, MDF and other wood composites, plastics, and solid surface materials DESCRIPTION Unique in that this cutter will trim the top and bottom edges of a panel simultaneously, whilst the centrally mounted bearing follows the profile.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Engravers STC

    £38.23£67.28
    STC 'Nib' Engraving Specially developed for engraving house names, bench plaques and other memorial inscriptions. The STC three flute 60 degree engraver is an ideal cutter for long production engraving work.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • With either an up or downward cutting action the rougher / hogging design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action,, For use with CNC machines.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • With either an up or downward cutting action the chipbreaker design allows for faster feed rates where end finish is less important. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • With either an up or downward cutting action. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • With an up and downard cutting action on the one tool, the fluted compression style allows for fine finish on the top and bottom edges of the board. NEG code denotes downward cutting action, POS code denotes upward cutting action, For use with CNC machines.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • British made two flute TCT top bearing guided profile flush trimming cutters. Gives a superb clean finish on timber, veneers and plastic laminate. The top bearing is for following a pattern or template to give a superb finish when replicating components.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Select options This product has multiple variants. The options may be chosen on the product page Details
  • Tapered Repair Cutter TCT

    £56.54£64.37
    Tapered Repair Cutter Designed specifically to repair small imperfections in solid surface material.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TCT Adjustable Top and Bottom Chamfer with Bearing DESCRIPTION For bevelling and trimming the top and bottom edges of the workpiece. Adjust the four wing trimmer blocks with spacers for differing widths of material. Maximum material thickness 15mm for the DCB16 and is fixed Maximum material thickness 32mm, minimum material thickness 16mm for the BCS38. Maximum material thickness 36mm, minimum material thickness 19mm for the BGAC45. To extend the life of cutting edges use 26mm bearing.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Dovetail TCT

    £33.64£74.94
    TCT Dovetail Standard sizes for all dovetail and sliding dovetail applications ie slot dovetail, hidden dovetail, etc. DESCRIPTION Available with scribers on TTDCS14.3-8 & TTDCS127-1/4 to enable use in conjunction with portable routing jigs. Parts TTADC12B-1/4, TTBDC14B-1/4 have shank mounted bearings fitted.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Ball Slot TCT

    £61.17£101.28
    BALL GROOVER SINGLE FLUTE TCT A range of single flute ball slot cutters designed for pipe and cable laying into timber and MDF. DESCRIPTION Important - cut neck slot first, do not run on neck but use a side fence or guide. NB The neck does not cut. Suggested cutters for neck slot: TTM716 for TTTSB127 neck diameter 6.5mm; TTM1020 for TTTSB254 neck diameter 9.5mm; TTM1325 for TTTSB32 neck diameter 12.7mm
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Finger Pull TCT

    £129.98£149.86
    CT Finger Pull Grip Square Bottom For solid handles and pulls on kitchen and wall unit doors, the perfect solutions for providing positive grips and softened, easy-on-the-fingers edges without the need for external hardware. DESCRIPTION TTFPC22 is a variation of TTFPC19 giving a square bottom and undercut. Both of these have a centre tip for plunging
    Select options This product has multiple variants. The options may be chosen on the product page Details