-
British made bearing guided chamfers with TCT tips for clean accurate cutting and fast clearance of waste materials. -
British made TCT Cove Cutters with two flutes for a cleaner finish. Ideal for making radiused grooves for decorative finishes etc. When making deeper channels take several passes. -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
DESCRIPTION A comprehensive range of Core Box, Cove, Radius, Guttering cutters with radii from 1.6mm to 25.4mm. Cutters with part number starting TTCBB have a shank mounted bearing fitted. -
SPOILBOARD SURFACE PLANER 2 & 3 WING TCT For trimming aluminium flashing. DESCRIPTION TTSMC20 has a shear action for finer finish. -
RouterBorer These are a designed for use at a faster RPM than standard boring bits for recessing circular hinges. A template and a guide will ensure accurate hole placement on the workpiece and that the router itself is secure with no sideways movement DESCRIPTION The CB version have chip breakers for use on more fibrous materials. The design allows the tool to run at speeds of 1000-20,000 RPM. -
British made two flute TCT bottom bearing guided rebate cutters & stepped rebate cutter. These rebate cutters can be used for manufacturing rebates, rebated corners, lap joints, tongues etc. When a full rebate is required make two passes. -
TCT Cove Mould Bearing Guided Producing a quarter round on the edge of the workpiece these are ideal for detailing casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables. DESCRIPTION These cutters come complete with TTB127 and TTB16 bearings. Matching rounding over cutters available for rule joints. -
DESCRIPTION To achieve a perfect tongued and grooved joint for flooring and paneling use the TTFFC28 in conjunction with a TTG35552-6.35 mini groover ( for the groove ). The same arbor can be used for the TTFFC28 and TTFA20 The TTFA20 is also for use with the TTLDTA style of arbor. -
TCT Slotting Ideal for slots in pencil box lids etc and internal slotting work. Suitable for intumescent fireproof strip. -
TCT Chamfer With Guide Pin A range of 45 and 30 degree chamfer cutters designed with a fixed small diameter guide pin. DESCRIPTION Useful for internal work where the small diameter pin enables right angle corners to be included. Popular in the sign making industry as they can chamfer the edges of plastic materials . -
DESCRIPTION 2 wing with or without centre point and with or without scribers, shanks are 10mm with flat on one side and end adjusting screw. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
Pin diameter is 5.5mm by 5.5mm long -
British made TCT self guided corner bead cutter with two flutes for a cleaner finish. Ideal for making beautifull edge moulds for decorative finishes etc. Full corner beads can be made by making a second pass at 90 degrees. -
DESCRIPTION 2 wing with centre point and with or without scribers and parallel shanks. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
Radiused 'V' Grooving TCT Ideal for panel and veining work, lettering, engraving, sign making, fluting, decorative trimming and barley twist. DESCRIPTION These do not cut to a point and will leave a 1mm - 2mm flat at the bottom of the groove. -
British made TCT Trade cutters for Aquamac and Intumescent Strips. Use E207HTC for Aquamac 21, E206HTC for Aquamac 63. -
Profile Edge Mould Decorative TCT The TTDEC range of tools are perfect for enhancing the appearance of square edged timber many of which offer balanced moulds for use on sections of woodwork at the centre of the design. -
TCT Stair Nosing This range have a flatter style to a standard full bull nose offering an alternative profile on stair treads, window boards and these can also be used to relieve sharp corners on the standard board thickness. DESCRIPTION The TTSNCB10 has a bottom bearing. -
TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip. -
TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand -
TCT Capillary Water Channel Groove All cutters in this range are non plunging but with bottom cutting action. DESCRIPTION This is designed to place a capillary groove on sill sections when used on site in a portable machine. -
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical -
TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section. -
A range of Grecian and Roman Ovolo Effect cutters, essential for faithful matching of Georgian window repair or production. -
TCT Profile Edge Mould This range of edge moulding offers a varied selection of profiles for table edgings -
These cutters can be used as matched sets of flute and beads or as individual sunk bead and reads. TTDSB8, TTDSB9 and TTDSB10 are suitable for moulding table surrounds and capillary drip grooves for window surrounds. TTRDSB8, TTRDSB9 and TTRDSB10 are matched to the TTDSB8, TTDSB9 and TTDSB10 range for the production of strip planking. -
TCT Bevelled With Bottom Radius A range of bevelled cutters with a bottom radius ideal for scallop fluting and finger pull applications.
-
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
TCT Weatherseal Recessing & Seals The perfect weatherstrip cutter, ideal for use with a portable router on site. DESCRIPTION TTWSC2 is used without a bearing. TTWSC3 has a 90mm overall length to suit 40-50mm rebate on doors. TTWSC4 routs a 2.7mm groove, 6mm deep. TTWSC5 suits the slot seal Carripile I weatherstrip system. TTSSC1 is a Smoke Seal cutter, designed to run off the bearing and give correct depth of cut to take a Quick Fit Smoke Seal Strip.
