-
TCT RPS Bevel Hole These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. DESCRIPTION These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. TTXC906-18 and TTXC906-23 bevel plug cutters can be used to make accurate plugs for the holes produced by the TTXC901 range of bevel hole cutters. -
TCT Two Flute Bowl Aperture Trimmer Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. DESCRIPTION Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. -
TCT Two Flute Box Cove For fine work to produce double radius in one pass, adjustable should material thicknesses vary. DESCRIPTION A further extension of the guttering cutter range with deeper cut for shallow fingerpull applications. Can also be used for cove cut on worktop upstands. For use with a template and guide bush for draining board grooves. Is suitable for producing grooves to take insulation rods. -
TCT Double Flute Primarily used to produce drain board channels. For use with template and guide bush. DESCRIPTION Primarily used to produce drain board channels. For window sections, designed to help displace water and moisture off window and door frames. Can also be used as soap dish cutter. For use with template and guide bush. -
TCT Four Flute Cutter For grooving and heavy rebate work. -
TCT Four Wing Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. Lower illustration shows method of removing bowl from worktop. DESCRIPTION Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. -
Produces a slot to take inlays of a different col0ur to produce a line effect joint -
TCT Double Flute Mini trimmers give a super fine finish. Ideal for cutting out small recesses in wall cladding for electrical fittings and suitable for trimming inlay flush and other trimming operations. Use TTTB22 Bearing for trimming overhanging countertops on undermount bowls. -
TCT Double Flute For edging sinks and vanity bowls. The special taper on the Bearing sleeve allows for perfect guide following around the inside of the bowl. -
TCT Double Flute For bevelling inside bowl tops and similar applications. Avoids need to turn workpiece. -
TCT Double Flute Fitted with self-guiding Bearing for rounding over. See cutters TTXC301 and TTXC321 for complete rounding over. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
TCT Bullnose Staff Bead A full bullnose radius for stair treads, nosings, window boards and edge mouldings Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
TCT Weatherseal Recessing & Seals The perfect weatherstrip cutter, ideal for use with a portable router on site. DESCRIPTION TTWSC2 is used without a bearing. TTWSC3 has a 90mm overall length to suit 40-50mm rebate on doors. TTWSC4 routs a 2.7mm groove, 6mm deep. TTWSC5 suits the slot seal Carripile I weatherstrip system. TTSSC1 is a Smoke Seal cutter, designed to run off the bearing and give correct depth of cut to take a Quick Fit Smoke Seal Strip. -
British made TCT Trade cutters for Aquamac and Intumescent Strips. Use E207HTC for Aquamac 21, E206HTC for Aquamac 63.
