-
This range of single flute RT cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design in allows a perfect V in the bottom of the groove. The tips are reversible and sold in boxes of 10. -
Tapered Repair Cutter Designed specifically to repair small imperfections in solid surface material. -
TCT Double Flute These cutters are designed to produce top surface perfect butt joints. Suitable for materials 6mm (15/64 inch) to 17mm (43/64 inch) thick. -
TCT Double Flute Mini trimmers give a super fine finish. Ideal for cutting out small recesses in wall cladding for electrical fittings and suitable for trimming inlay flush and other trimming operations. Use TTTB22 Bearing for trimming overhanging countertops on undermount bowls. -
This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility. -
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work. -
TCT Corner Ovolo Profiles and moulds in one operation. Ideal for aperture cutting, ie snooker table pockets, worktops and cover mouldings. DESCRIPTION WCO Type have plunge facility. WCOB Type have bearing. -
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical -
TCT Profile Edge Mould This range of edge moulding offers a varied selection of profiles for table edgings -
TCT Dovetail Standard sizes for all dovetail and sliding dovetail applications ie slot dovetail, hidden dovetail, etc. DESCRIPTION Available with scribers on TTDCS14.3-8 & TTDCS127-1/4 to enable use in conjunction with portable routing jigs. Parts TTADC12B-1/4, TTBDC14B-1/4 have shank mounted bearings fitted.
