-
TCT Double Flute These cutters are designed to produce top surface perfect butt joints. Suitable for materials 6mm (15/64 inch) to 17mm (43/64 inch) thick. -
TCT Double Flute Fitted with self-guiding Bearing for rounding over. See cutters TTXC301 and TTXC321 for complete rounding over. -
TCT Two Flute Bowl Aperture Trimmer Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. DESCRIPTION Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
UP/DOWN SHEAR STAGGERED TOOTH TCT A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. DESCRIPTION A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
TCT Ogee Used for paneling and edge moulding for that classic ogee feature. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation. -
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
TCT Raised Panel Grecian Ogee Ideal for heavy cornice and dado rail production. Used in restoration and as a classic mould for picture frames, to produce raised panels on drawer fronts and doors. -
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
DOWNCUT SHEAR DOUBLE FLUTE TCT Shear action downcut to reduce breakout. DESCRIPTION For short producton runs only. For longer and improved performance see our Solid Carbide Range. *These tools are designed to give a 'tear' free groove in conjunction with a tight housed joint when using plywood. -
Profile Edge Mould Decorative TCT The TTDEC range of tools are perfect for enhancing the appearance of square edged timber many of which offer balanced moulds for use on sections of woodwork at the centre of the design. -
Left Hand Rotation 3 Wing With 3 Scribers and Centre Point A comprehensive range of hinge borers. Please ensure correct variation is selected when ordering. DESCRIPTION A comprehensive range of hinge borers. All are available in 57mm overall lengths. Some 2 wing with 2 scribers cutters are also available in 70mm and 77mm overall lengths. All have 10mm diameter Left Hand or Right Hand Shanks. Shanks have flat on one side and length adjusting screw. Some sizes are also available with or without centre point. The TTTMB range have a removable/replaceable centre point with a 'V' point effect at one end, flush finish at the other end. Please ensure correct variation is selected when ordering. For use on Multi-Boring machines. -
2 Wing with C/Point without Scribers TCT 2 wing available with or without scribers and parallel shanks. DESCRIPTION 2 wing available with or without scribers and parallel shanks. Right hand with centre point. Left hand available to special order - please contact the Sales Department for details. For boring bits at above 80mm overall length please contact the Sales Department for pricing and availability. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Select correct boring bit design for machine, material and thickness: Drill or Boring Machines: Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
Groover TCT Titman's Wobble Saw is the traditional answer to the problem of cutting various widths of grooves in timber, chipboard and other man-made materials. DESCRIPTION Titman's Wobble Saw is the traditional answer to the problem of cutting various widths of grooves in timber, chipboard and other man-made materials. The steel boss and blade vary the Kerf from 6mm to 22mm when set to the calibrated reading. The eight tunsten carbide tips have a shear action to give a clean and precise groove width. Varied bore sizes can be offered. Please state requirements when ordering. -
TCT Double Flute For creating a 'step down' shadow line between bowl and sheet. -
TCT Double Flute TTXC611 is the perfect cutter for panel raising work. TTXC616 is designed for large 45 degree chamfer work with guide Bearing. -
TCT Double Flute This cutter produces a 'waterfall' effect on a worktop. Can be used against a wall for splashback. -
TCT Double Flute Great care should be exercised when using this cutter to avoid 'cutter wander'. Use correct jig, template or side fence. Use a guide bush in conjunction with an offset template. -
TCT Two Flute Hob Cutter Used to produce, in one pass, the aperture in which the hob unit sits. -
7 PIECE TCT RPS Cutter Set 1/2 Shanks Specially made tooling for repair of 'wrongly made' holes and also for decorative effects using plugs in other colours. This set includes all the TTXC901 and TTXC906 cutters. DESCRIPTION Use the Titman Plug system for a perfect repair. Specially made tooling for repair of 'wrongly made' holes and also for decorative effects using plugs in other colours. This set includes all the TTXC901 and TTXC906 cutters. -
TCT Weatherseal Recessing & Seals The perfect weatherstrip cutter, ideal for use with a portable router on site. DESCRIPTION TTWSC2 is used without a bearing. TTWSC3 has a 90mm overall length to suit 40-50mm rebate on doors. TTWSC4 routs a 2.7mm groove, 6mm deep. TTWSC5 suits the slot seal Carripile I weatherstrip system. TTSSC1 is a Smoke Seal cutter, designed to run off the bearing and give correct depth of cut to take a Quick Fit Smoke Seal Strip. -
TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section. -
CT Plug Making Drilling machines only. DESCRIPTION Drilling machines only. Can be used with the CSD range of Countersink Drills and CBD range of Counterbore Drills. Maximum Plug Depth=16mm for all cutters. TTPMC8 Plug Diameter=9.5mm, No. 8 Wood Screw TTPMC9 Plug Diameter=10mm TTPMC10 Plug Diameter=12mm, No. 10 Wood Screw TTPMC127 Plug Diameter=12.7mm TTPMC12 Plug Diameter=16mm, No. 12 Wood Screw -
TCT Minature Bead Cutters A range of minature beading cutters for fine decorative work. These cutters perform best at 24,000 RPM. -
Right Hand Drill TCT Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter. Drilling machines only - not for use on portables. DESCRIPTION Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter (see below). Drilling machines only - not for use on portables. All drills 20mm long. TTCSD8 (1/4 inch Shank) and TTCSD9.5 (10mm Shank): Countersink Diameter D=9.5mm (matches plug produced by TTPMC8), Drill Diameter d=4.8mm, No. 8 Wood Screw TTCSD10 (1/4 inch Shank) and TTCSD12 (10mm Shank): Countersink Diameter D=12mm (matches plug produced by TTPMC10), Drill Diameter d=5.5mm, No. 10 Wood Screw TTCSD12 (1/4 inch Shank) and TTCSD16 (10mm Shank): Countersink Diameter D=16mm (matches plug produced by TTPMC12), Drill Diameter d=6.35mm, No. 12 Wood Screw -
TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes. -
TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
Profile Edge Mould Classic Lambs Tongue TCT Bearing Guided Classic Lambs Tongue mould perfect for finishing table and furniture tops. DESCRIPTION These cutters are supplied with a 9.5mm diameter bearing and a 12.7mm diameter bearing. -
TCT Chamfering Edge Chamfering Edge Cutters. Reducing and Chamfering. DESCRIPTION TTCEC45, TTCECR45, TTLTC4, TTLTCR4, TTLTC63, TTLTCR63 are non plunge but with bottom cut facility. TTCECR45 is the reverse of TTCEC45. TTCECR45L is the reverse of TTCEC45L. TTLTC4 and TTLTCR4 give a lambs tongue effect as TTROB range. TTLTCR4 is the reverse of TTLTC4. TTLTCR63 is the reverse of TTLTC63. -
All these blades have a positive cutting angle which make them suitable for wood and wood composites. To be used on portable machines and mitre saws. Excelent for cutting across the grain. All these blades are alternate top bevel (ATB) and Tungsten carbide Tipped (TCT). -
These scoring blades are ideal for Laminates, Bi Laminates and Veneers. They have an ATB tooth with a 5 degree positive cutting angle. Maximum scoring depth 2mm. For Scoring Melemine on bilaminated chipboard and MDF panels. All these blades are alternate top bevel (ATB) and Tungsten carbide Tipped (TCT). -
Produces a slot to take inlays of a different col0ur to produce a line effect joint -
TCT Double Flute Helps to reduce the effect of overlay joint line. DESCRIPTION Sometimes called 'waterfall effect' giving a non-drip edge to a worktop. TTXC214 has a shorter cut length, ideal for use on 12.5mm thick material. TTXC216 is fitted with self-guided Bearing for use with 15mm thick material. TTXC221 is ideal for use on 19mm (3/4 inch) thick material. -
TCT Two Flute Ventilation Slot Slots and produces a radius on the upper edge in one pass. -
TCT Two Flute Adjustable Double Radius Use with 1/2 inch thick material produces double radius in one pass. -
TCT Two Flute Rounding Over Fitted with a Shank mounted Bearing. First cut with TTXC301, finshing using matching TTXC321. Eliminates flat on edge. -
TCT Two Flute Spanish Edge with Bearing For all types of decorative edge profiling. -
TCT Double Flute For bevelling inside bowl tops and similar applications. Avoids need to turn workpiece. -
DESCRIPTION This cutter is used to enhance the edge of the worktop -
TCT Four Flute Cutter For grooving and heavy rebate work. -
TCT Two Flute Cove Mould With Bearing Two flute half round cutter. Ideal for a scalloped edge finish. For all types of decorative edge profiling. -
TCT RPS Bevel Hole These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. DESCRIPTION These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. TTXC906-18 and TTXC906-23 bevel plug cutters can be used to make accurate plugs for the holes produced by the TTXC901 range of bevel hole cutters. -
TCT Capillary Water Channel Groove All cutters in this range are non plunging but with bottom cutting action. DESCRIPTION This is designed to place a capillary groove on sill sections when used on site in a portable machine. -
TCT Multi-Mould DESCRIPTION TTTOR25 gives an ornate moulding used in full or in part. TTTOR22 is a possible picture rail and cover mould cutter. TTTOR27 ideal to use the complete mould or part for short production runs. Excellent cutter to produce ornate skirting and architrave moulding. TTTOR-B gives a deep cavetto effect with a bead to break up the line of the mould. The fine lines of this cutter make it an excellent choice for matching skirting and architrave. TTTOR-C is a variation of the Torus Mould (TTTOR-T). -
DESCRIPTION To achieve a perfect tongued and grooved joint for flooring and paneling use the TTFFC28 in conjunction with a TTG35552-6.35 mini groover ( for the groove ). The same arbor can be used for the TTFFC28 and TTFA20 The TTFA20 is also for use with the TTLDTA style of arbor. -
TCT Stair Nosing This range have a flatter style to a standard full bull nose offering an alternative profile on stair treads, window boards and these can also be used to relieve sharp corners on the standard board thickness. DESCRIPTION The TTSNCB10 has a bottom bearing. -
Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006 -
TCT Machine Countersink & Bores A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
Pin diameter is 5.5mm by 5.5mm long
-
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
-
RouterBorer These are a designed for use at a faster RPM than standard boring bits for recessing circular hinges. A template and a guide will ensure accurate hole placement on the workpiece and that the router itself is secure with no sideways movement DESCRIPTION The CB version have chip breakers for use on more fibrous materials. The design allows the tool to run at speeds of 1000-20,000 RPM. -
A range drills with a 1mm long 45 degree chamfer on the tip edge for use in the specialized boring machine MAFELL DuoDübler . Shanks are 8mm diameter with a flat on one side and length adjusting screw in the end. Available with right hand. -
TCT Classical Perfect for drawer fronts in solid material for enhancing the style and appearance of panelled work. -
TCT Bevelled With Bottom Radius A range of bevelled cutters with a bottom radius ideal for scallop fluting and finger pull applications.
