-
Groover TCT Titman's Wobble Saw is the traditional answer to the problem of cutting various widths of grooves in timber, chipboard and other man-made materials. DESCRIPTION Titman's Wobble Saw is the traditional answer to the problem of cutting various widths of grooves in timber, chipboard and other man-made materials. The steel boss and blade vary the Kerf from 6mm to 22mm when set to the calibrated reading. The eight tunsten carbide tips have a shear action to give a clean and precise groove width. Varied bore sizes can be offered. Please state requirements when ordering. -
All these blades have a positive cutting angle which make them suitable for wood and wood composites. To be used on portable machines and mitre saws. Excelent for cutting across the grain. All these blades are alternate top bevel (ATB) and Tungsten carbide Tipped (TCT). -
Ripping Saw Blade Saw Blades with anti-kickback device. Suitable for ripping hard and soft wood. DESCRIPTION Saw Blades with anti-kickback device. Suitable for ripping hard and soft wood. -
PRICES REDUCED - LIMITED STOCKS Non stick Coated Tungsten Carbide Tipped Sawblades for machines from 200mm upwards in diameter -
PRICES REDUCED - LIMITED STOCKS Non stick Coated Tungsten Carbide Tipped Sawblades for machines up to 199mm in diameter -
Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006 -
TCT Weatherseal Recessing & Seals The perfect weatherstrip cutter, ideal for use with a portable router on site. DESCRIPTION TTWSC2 is used without a bearing. TTWSC3 has a 90mm overall length to suit 40-50mm rebate on doors. TTWSC4 routs a 2.7mm groove, 6mm deep. TTWSC5 suits the slot seal Carripile I weatherstrip system. TTSSC1 is a Smoke Seal cutter, designed to run off the bearing and give correct depth of cut to take a Quick Fit Smoke Seal Strip. -
A range of Grecian and Roman Ovolo Effect cutters, essential for faithful matching of Georgian window repair or production. -
TCT Rounding Over A unique cutter designed for short skirting production, or for relieving a square section. -
TCT Multi-Mould DESCRIPTION TTTOR25 gives an ornate moulding used in full or in part. TTTOR22 is a possible picture rail and cover mould cutter. TTTOR27 ideal to use the complete mould or part for short production runs. Excellent cutter to produce ornate skirting and architrave moulding. TTTOR-B gives a deep cavetto effect with a bead to break up the line of the mould. The fine lines of this cutter make it an excellent choice for matching skirting and architrave. TTTOR-C is a variation of the Torus Mould (TTTOR-T). -
DESCRIPTION To achieve a perfect tongued and grooved joint for flooring and paneling use the TTFFC28 in conjunction with a TTG35552-6.35 mini groover ( for the groove ). The same arbor can be used for the TTFFC28 and TTFA20 The TTFA20 is also for use with the TTLDTA style of arbor. -
TCT Capillary Water Channel Groove All cutters in this range are non plunging but with bottom cutting action. DESCRIPTION This is designed to place a capillary groove on sill sections when used on site in a portable machine. -
TCT Two Flute Ventilation Slot Slots and produces a radius on the upper edge in one pass. -
RouterBorer These are a designed for use at a faster RPM than standard boring bits for recessing circular hinges. A template and a guide will ensure accurate hole placement on the workpiece and that the router itself is secure with no sideways movement DESCRIPTION The CB version have chip breakers for use on more fibrous materials. The design allows the tool to run at speeds of 1000-20,000 RPM. -
Pin diameter is 5.5mm by 5.5mm long
-
UP/DOWN SHEAR STAGGERED TOOTH TCT A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. DESCRIPTION A fine finish may be achieved for trimming veneered and double-faced boards, plywoods and natural timbers using these up-down two flute cutters. -
TCT Profile Edge Mould This range of edge moulding offers a varied selection of profiles for table edgings -
TAPERED DOUBLE FLUTE TCT Two flute cutters with taper designed for constructing vacuum forming moulds. DESCRIPTION Two flute cutters with taper designed for constructing vacuum forming moulds. 2 degree tapered side allows easier release. TTH58212T can produce a leading edge on a door. -
Profile Edge Mould Decorative TCT The TTDEC range of tools are perfect for enhancing the appearance of square edged timber many of which offer balanced moulds for use on sections of woodwork at the centre of the design. -
HINGE AND FIRE STRIP RECESSER TCT A cutter ideal for hinge recessing and the underside of handrails, these have extra long shanks for use with the popular hinge jigs on the market -
TCT Bevelled With Bottom Radius A range of bevelled cutters with a bottom radius ideal for scallop fluting and finger pull applications.
-
TCT Two Flute Adjustable Double Radius Use with 1/2 inch thick material produces double radius in one pass. -
SPOILBOARD SURFACE PLANER 2 & 3 WING TCT For trimming aluminium flashing. DESCRIPTION TTSMC20 has a shear action for finer finish. -
TCT Stair Tread Housing A range of cutters for the popular sizes of stair treads for use in conjunction with jigs and trenching machines. For the stair trenching machines some cutters are offered in both rotation, left and right hand -
TCT Stair Nosing This range have a flatter style to a standard full bull nose offering an alternative profile on stair treads, window boards and these can also be used to relieve sharp corners on the standard board thickness. DESCRIPTION The TTSNCB10 has a bottom bearing. -
DOWNCUT SHEAR DOUBLE FLUTE TCT Shear action downcut to reduce breakout. DESCRIPTION For short producton runs only. For longer and improved performance see our Solid Carbide Range. *These tools are designed to give a 'tear' free groove in conjunction with a tight housed joint when using plywood. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
TCT Slotting Ideal for slots in pencil box lids etc and internal slotting work. Suitable for intumescent fireproof strip. -
Screws, Nuts, Washers, Allen Keys and Collars
-
DESCRIPTION -
TCT Two Flute Rounding Over Fitted with a Shank mounted Bearing. First cut with TTXC301, finshing using matching TTXC321. Eliminates flat on edge. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
TCT Two Flute Spanish Edge with Bearing For all types of decorative edge profiling. -
Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings. -
These scoring blades are ideal for Laminates, Bi Laminates and Veneers. They have an ATB tooth with a 5 degree positive cutting angle. Maximum scoring depth 2mm. For Scoring Melemine on bilaminated chipboard and MDF panels. All these blades are alternate top bevel (ATB) and Tungsten carbide Tipped (TCT). -
CT Plug Making Drilling machines only. DESCRIPTION Drilling machines only. Can be used with the CSD range of Countersink Drills and CBD range of Counterbore Drills. Maximum Plug Depth=16mm for all cutters. TTPMC8 Plug Diameter=9.5mm, No. 8 Wood Screw TTPMC9 Plug Diameter=10mm TTPMC10 Plug Diameter=12mm, No. 10 Wood Screw TTPMC127 Plug Diameter=12.7mm TTPMC12 Plug Diameter=16mm, No. 12 Wood Screw -
TCT Tapered Plug Making Plug making cutter producing a tapered plug to be driven in and tightly secured. To avoid cutter deflection use this TTTPC range of cutters only on Pillar Drilling machines and do not exceed 3,000 RPM. Feed evenly into material. DESCRIPTION Plug making cutter producing a tapered plug to be driven in and tightly secured. To avoid cutter deflection use this TTTPC range of cutters only on Pillar Drilling machines and do not exceed 3,000 RPM. Feed evenly into material. -
Twist Drills Slow Spiral for plastics, brass, chipboard and MDF DESCRIPTION The design of the slow spiral drills are better suited for use with the counterbore and countersink ranges as they help to prevent clogging. (over the faster helix versions.) -
Shankless Counterbore For Pillar drilling machines only, not on portables. DESCRIPTION For Pillar drilling machines only, not on portables. Drills and Allen Keys not included. Available in TCT (part codes suffixed TCT) and Silver Steel (part codes suffixed SS) and to suit a selection of drill hole diameters. Please ensure correct variation is selected when ordering. -
Left Hand TCT A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
TCT Machine Countersink & Bores A range of Countersinks and Counterbores. DESCRIPTION A range of Countersinks (part codes prefixed CS) and Counterbores (part codes prefixed CB). Both are 45mm Overall Length and have 10mm diameter Shanks with a flat on one side. Counterbores have length adjusting screw. Available in Left Hand (part codes suffixed LH) and Right Hand (part codes suffixed RH) rotation, and for drill hole diameters 3/16 inch (part codes containing -3/16) and 5mm (part codes containing -5). Please ensure correct variation is selected when ordering. Drills not included in price. -
Countersink Shankless SS For Pillar drilling machines only, not on portables. -
TCT Minature Bead Cutters A range of minature beading cutters for fine decorative work. These cutters perform best at 24,000 RPM. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
DESCRIPTION This cutter is used to enhance the edge of the worktop -
Left Hand Counter Sink TCT Designed to fit metric boring bits with 10mm Shank. Suitable for 'V' point drills, Lip and Spur and most dowel drills. DESCRIPTION Designed to fit metric boring bits with 10mm Shank. Left Hand or Right Hand rotation. Suitable for 'V' point drills, Lip and Spur and most dowel drills. TTMBC4/10 for fixing onto the Shank section, for drill diameter 4-10mm. TTMBCF range for fixing directly onto the Flute section. -
Right Hand Drill TCT Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter. Drilling machines only - not for use on portables. DESCRIPTION Lip and Spur. Used in conjunction with the TTPMC range producing perfect drill and countersinking to take plug produced by TTPMC plug cutter (see below). Drilling machines only - not for use on portables. All drills 20mm long. TTCSD8 (1/4 inch Shank) and TTCSD9.5 (10mm Shank): Countersink Diameter D=9.5mm (matches plug produced by TTPMC8), Drill Diameter d=4.8mm, No. 8 Wood Screw TTCSD10 (1/4 inch Shank) and TTCSD12 (10mm Shank): Countersink Diameter D=12mm (matches plug produced by TTPMC10), Drill Diameter d=5.5mm, No. 10 Wood Screw TTCSD12 (1/4 inch Shank) and TTCSD16 (10mm Shank): Countersink Diameter D=16mm (matches plug produced by TTPMC12), Drill Diameter d=6.35mm, No. 12 Wood Screw -
TCT Chamfering Edge Chamfering Edge Cutters. Reducing and Chamfering. DESCRIPTION TTCEC45, TTCECR45, TTLTC4, TTLTCR4, TTLTC63, TTLTCR63 are non plunge but with bottom cut facility. TTCECR45 is the reverse of TTCEC45. TTCECR45L is the reverse of TTCEC45L. TTLTC4 and TTLTCR4 give a lambs tongue effect as TTROB range. TTLTCR4 is the reverse of TTLTC4. TTLTCR63 is the reverse of TTLTC63. -
TCT Ogee Used for paneling and edge moulding for that classic ogee feature. -
Left Hand Rotation 3 Wing With 3 Scribers and Centre Point A comprehensive range of hinge borers. Please ensure correct variation is selected when ordering. DESCRIPTION A comprehensive range of hinge borers. All are available in 57mm overall lengths. Some 2 wing with 2 scribers cutters are also available in 70mm and 77mm overall lengths. All have 10mm diameter Left Hand or Right Hand Shanks. Shanks have flat on one side and length adjusting screw. Some sizes are also available with or without centre point. The TTTMB range have a removable/replaceable centre point with a 'V' point effect at one end, flush finish at the other end. Please ensure correct variation is selected when ordering. For use on Multi-Boring machines. -
DESCRIPTION 2 wing with centre point and with or without scribers and parallel shanks. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
DESCRIPTION 2 wing with or without centre point and with or without scribers, shanks are 10mm with flat on one side and end adjusting screw. Right hand with centre point. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM. -
2 Wing with C/Point without Scribers TCT 2 wing available with or without scribers and parallel shanks. DESCRIPTION 2 wing available with or without scribers and parallel shanks. Right hand with centre point. Left hand available to special order - please contact the Sales Department for details. For boring bits at above 80mm overall length please contact the Sales Department for pricing and availability. These boring bits must be used in fixed head machines only, never in hand-held routing machines or hand-held drills. Select correct boring bit design for machine, material and thickness: Drill or Boring Machines: Softwood, Chipboard - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Hardwood - Use Scribers: 15mm-35mm 3000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. MDF - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 1500 RPM. Laminate - Use Scribers: 15mm-35mm 3000-6000 RPM, 35mm-50mm 3000 RPM, 50mm-100mm 2000 RPM. Diameters of 20mm and above with Scribers will burn at over 6000 RPM. Do not use Scribers on solid laminates. Router Machines: Softwood, Hardwood, Chipboard, MDF, Laminate - No Scribers over 6000RPM: 15mm-35mm 10000 RPM, 35mm-50mm 6000 RPM, 50mm-100mm 3000 RPM.
-
TCT Lip and Spur Dowell Drills For use in plunge routers and drilling machines, the slow spiral design allow these tools to run at a higher RPM than standard drills. The sizes offered here produce the correct hole diameter for the sizes needed for popular dowel sizes. -
A range of lip and spur drills with 10mm diameter parallel shanks. Available with right hand rotation. -
TCT Undercut With Bearing A range of cutters used to produce a recess on the underside of lettering. DESCRIPTION A range of cutters used to produce a recess on the underside of lettering. -
Barley Twist TCT A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Can also be used for edge profiling. DESCRIPTION A range of cutters which are ideal for producing barley twist designs for chair legs and pilaster fluting. Please also see the TTGC and the Ogee range for alternative cutters that may be used for fluting. TTBTC1 - Astragal Effect gives an extra feature to turned parts. Can also be used as an edge profile or special panel effect. TTBTC2 - This Shallow Radius cutter is very popular for standard barley twist design. Ideal for use on heavy duty lathes with routing attachment. TTBTC3 - This Ovolo Cutter is a deeper version of TTBTC2. Can be used for engraving when used with a CNC router machine. TTBTC4 - This Double Radius Effect cutter can be used as an edge mould cutter. TTBTC5 - The largest Ogee Effect cutter in this range. An ideal choice for flat roping or parallel fluting. TTBTC6 - The smaller version of the TTBTC5 Ogee Cutter. Can also be used for roping effect and fluting as well as panel raising. -
TCT Raised Panel Grecian Ogee Ideal for heavy cornice and dado rail production. Used in restoration and as a classic mould for picture frames, to produce raised panels on drawer fronts and doors. -
Downturn Rebate Cutter Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. Lower illustration shows method of removing bowl from worktop. DESCRIPTION To produce a 13mm rebate for the downturns on solid surface worktops. Fitted with a plastic sleeved bearing TTPB127. -
TCT Four Flute Cutter For grooving and heavy rebate work. -
ACM FOLDING AND SCORING TCT These cutters are specially deigned for routing aluminium composite material. Used to rout V-grooves of 90 degree, 108 degree or 135 degree inclusive into the centre of the material for the folding the ACM into a 90 degree, 72 degree or 45 degree corner, this procedure will allow easy foldinging of the material preventing the cracking in the intended folded area. -
Profile Edge Mould Classic Lambs Tongue TCT Bearing Guided Classic Lambs Tongue mould perfect for finishing table and furniture tops. DESCRIPTION These cutters are supplied with a 9.5mm diameter bearing and a 12.7mm diameter bearing. -
Profile Edge Mould Classic Decor TCT Bearing Guided This classic shape is a fine cutter for reproduction furniture, bolection mould and any work in which the natural finish and beauty of wood is to be enhanced. -
TCT Classical Perfect for drawer fronts in solid material for enhancing the style and appearance of panelled work. -
TCT Edge Moulding Shallow Bead A shallow radius style bull nose cutter ideal for a hand hold which is able to plunge into the centre of a board. Designed to finish solid edged worktops for kitchens or display work areas. These have a shallow radius DESCRIPTION The shallow arc is ideal for a hand hold shape rather than a full 180-degree round over, this also has short flats above and below the cutter arc which can produce a small quirk effect for an edge mould for example -
TCT Moulding Edge Bead Heavy Duty A range of dual purpose edge moulding cutters designed to finish work tops and edges with a single bead mould or a full bullnose on the edge of material between 4mm to 12mm in thickness. -
TCT Bullnose Staff Bead A full bullnose radius for stair treads, nosings, window boards and edge mouldings Flats at top and bottom of the cutting edges create fillets on stock thicker than the nose diameter. -
TCT T-Slot Square Edged Designed for creating the T-slot in wall panels used in the point of sale industry for shelving and display purposes. -
TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames
