-
TCT Single Flute A high performance, single flute, cutter for extra clearance when cutting apertures and shaping work. The single flute gives a stronger backing support to the cutting edge. -
TCT Double Flute Shear action downcut to reduce breakout for longer life and improved performance. Pushes waste material away from the operator. -
TCT Double Flute Mini trimmers give a super fine finish. Ideal for cutting out small recesses in wall cladding for electrical fittings and suitable for trimming inlay flush and other trimming operations. Use TTTB22 Bearing for trimming overhanging countertops on undermount bowls. -
TCT Double Flute Fitted with self-guiding Bearing for rounding over. See cutters TTXC301 and TTXC321 for complete rounding over. -
TCT Double Flute These cutters are designed to produce top surface perfect butt joints. Suitable for materials 6mm (15/64 inch) to 17mm (43/64 inch) thick. -
TCT RPS Bevel Hole These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. DESCRIPTION These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. TTXC906-18 and TTXC906-23 bevel plug cutters can be used to make accurate plugs for the holes produced by the TTXC901 range of bevel hole cutters. -
This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10. -
The cutters still give a fantastic finish, great longevity of use and of course can be re-sharpened, a superb cutter at a very competitive price. -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
DESCRIPTION Special relief on the cutter body allows for deep slotting work. Suitable for plunging. Note:LH58L, LH58L2, LH34L, not to be used in a portable router. -
These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself. -
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work. -
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility. -
DESCRIPTION Supplied with 2 bearings, 12.7mm and 16mm in diameter, two shapes can produced with one cutter by changing the bearing size. The 16 mm diameter bearing removes the bottom quirk. -
TCT Cove Mould Bearing Guided Producing a quarter round on the edge of the workpiece these are ideal for detailing casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables. DESCRIPTION These cutters come complete with TTB127 and TTB16 bearings. Matching rounding over cutters available for rule joints. -
CT Finger Pull Grip Square Bottom For solid handles and pulls on kitchen and wall unit doors, the perfect solutions for providing positive grips and softened, easy-on-the-fingers edges without the need for external hardware. DESCRIPTION TTFPC22 is a variation of TTFPC19 giving a square bottom and undercut. Both of these have a centre tip for plunging -
British made two flute TCT top bearing guided profile flush trimming cutters. Gives a superb clean finish on timber, veneers and plastic laminate. The top bearing is for following a pattern or template to give a superb finish when replicating components. -
TCT T-Slot Square Edged Designed for creating the T-slot in wall panels used in the point of sale industry for shelving and display purposes. -
Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction. -
Profile Edge Mould Classic Roman Ogee TCT Bearing Guided Classic Roman Ogee used in any work needing a quality finish. DESCRIPTION One cutter - three shapes by changing bearing. Cutters supplied with 12.7mm and 16mm bearings. -
TCT Rounding Over With Guide Pin Available in fractional sizes to relieve corners on small panels, or larger radii for stair nosings, window boards and many shelf and display units. DESCRIPTION. Careful feeding will prevent the pin from marking workpiece. Pin diameter 8.9mm by 6.1mm long -
STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish. -
SINKING AND STRIP RECESSING TCT For library and book shelving strip/tonk strip. -
TCT Shark Nose Designed to finish off worktops, table tops and basic edge finishing requirements. Traditional once rounded and splay profile. Will radius hardwoods and softwood edgings, safe return design - ideal in kitchens, receptions and technical workplaces. -
SINGLE FLUTE SOLID CARBIDE For use on plastics, acrylics and light metals. The 'O' flute design reduces heat build up on low melting point materials. DESCRIPTION These straight single fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam, ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish and use the shortest cut lengths possible. The radius flute design gives effective cutting on ductile plastics, an ideal tool for cutting ABS components for example on 5 and 7 axis machines and offer efficient effective chip clearance with the for smooth feed rate that CNC's offer -
HINGE AND FIRE STRIP RECESSER TCT A cutter ideal for hinge recessing and the underside of handrails, these have extra long shanks for use with the popular hinge jigs on the market -
A range of Grecian and Roman Ovolo Effect cutters, essential for faithful matching of Georgian window repair or production. -
Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006
