9.5

  • Burrs and Rasps STC

    £16.83£133.04
    Solid Carbide Burrs Ideally suited for freehand stock removal, weld preparation and finishing of nimonic alloy components. A smooth finish can be achieved on metal, plastic and other materials. RPM for each product in this range: TTSCB1 - 10,000-30,000 TTSCB2 - 20,000-90,000 TTSCB3 - 10,000-30,000 TTSCB4 - 20,000-50,000 TTSCB5 - 10,000-30,000 TTSCB6 - 20,000-50,000 TTSCB7 - 10,000-30,000 TTSCB8 - 10,000-30,000 TTSCB9 and TTSCB95 - 20,000-50,000 TTSCB10 - 20,000-50,000 TTSCB11-TTSCB14 - 20,000-50,006
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Twist Drills Slow Spiral for plastics, brass, chipboard and MDF DESCRIPTION The design of the slow spiral drills are better suited for use with the counterbore and countersink ranges as they help to prevent clogging. (over the faster helix versions.)
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • A range of 60 degree inclusive V Point drills with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation.  
    Select options This product has multiple variants. The options may be chosen on the product page Details