1

  • Ball Slot TCT

    £61.17£101.28
    BALL GROOVER SINGLE FLUTE TCT A range of single flute ball slot cutters designed for pipe and cable laying into timber and MDF. DESCRIPTION Important - cut neck slot first, do not run on neck but use a side fence or guide. NB The neck does not cut. Suggested cutters for neck slot: TTM716 for TTTSB127 neck diameter 6.5mm; TTM1020 for TTTSB254 neck diameter 9.5mm; TTM1325 for TTTSB32 neck diameter 12.7mm
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Select options This product has multiple variants. The options may be chosen on the product page Details
  • Engravers STC

    £38.23£67.28
    STC 'Nib' Engraving Specially developed for engraving house names, bench plaques and other memorial inscriptions. The STC three flute 60 degree engraver is an ideal cutter for long production engraving work.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Keyhole Slot TCT

    £44.36£50.47
    TCT Keyhole Slotter Single flute keyhole slot router cutter for hanging items flush to a wall by making an aperture in the back of the workpiece. DESCRIPTION Ideal for the use with No 8 & No 10 screw heads for the application of hanging plaques, picture frames
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Panel Pilot Pierce and Trim TCT A very popular robust solid end plunge and guided panel pilot or pierce and trim cutter widely used within the caravan, mobile home and motor home manufacture industry, this is ideal for cutting apertures and openings in the walls and floor pans. DESCRIPTION The V point end design allows the cutter to plunging into the board and the solid guide immediately behind this is used as the follower. There are two options here in design with the single flute and double flute versions. A single flute cuts faster with good chip clearance which then has less friction, but can leave a rougher cut on certain materials. A double flute produces a cleaner finish with a slower feed rate The TTPDT127-1/2SF has a solid guide at the end and in the middle of two cutting edges allowing for the simultaneous trimming of a top and bottom covering over the wooden frame construction.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • This range of single flute RT cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design in allows a perfect V in the bottom of the groove. The tips are reversible and sold in boxes of 10.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Radius Cove TCT

    £30.59£133.04
    DESCRIPTION A comprehensive range of Core Box, Cove, Radius, Guttering cutters with radii from 1.6mm to 25.4mm. Cutters with part number starting TTCBB have a shank mounted bearing fitted.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • TC Replacement Tip for 'V' Grooving & Tracey Work With special programming, the TTVGC-RT range of cutters can produce a perfect right-angle corner. DESCRIPTION Using a normal angle cutter, the corners produced have a radius. With special programming, the TTVGC-RT range of cutters can produce a perfect right-angle corner. Reversible Knives are 12mm wide D mm and L mm values given are maximums.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DESCRIPTION Designed with a plunge facility for creating slots or channels for locks and drainage the relieved narrow neck section behind the cutting edge allows for a greater plunging depth.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DESCRIPTION These cutters are designed with a plunge facility for creating slots or channels for locks and drainage.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DESCRIPTION Made from solid tungsten carbide these are designed with a plunge facility for creating slots or channels for locks and drainage.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DESCRIPTION Water slot range of cutters with single straight flute design and a shorter relief slot on opposite side of cutting edge to assist plunging.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • STRAIGHT FLUTED SOLID CARBIDE For use on plastics, acrylics, composites and light metals . DESCRIPTION These straight double fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge.        
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Select options This product has multiple variants. The options may be chosen on the product page Details
  • Straight Single Flute TCT

    £33.64£38.23
    TCT Single Flute A high performance, single flute, cutter for extra clearance when cutting apertures and shaping work. The single flute gives a stronger backing support to the cutting edge.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • SINGLE FLUTE SOLID CARBIDE For use on plastics, acrylics and light metals. The 'O' flute design reduces heat build up on low melting point materials. DESCRIPTION These straight single fluted plunging solid carbide router cutters are ideal for use on plastics, acrylics, foam, ABS, aluminium and magnesium . Please ensure that the shank is inserted fully into the collet, this helps reduce vibration which causes a reduction in the quality of finish and use the shortest cut lengths possible. The radius flute design gives effective cutting on ductile plastics, an ideal tool for cutting ABS components for example on 5 and 7 axis machines and offer efficient effective chip clearance with the for smooth feed rate that CNC's offer
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • A particular advantage to this replacement tip style over the conventional brazed variety is that the diameter remains constant. These double and single flute style flush trim router cutters are designed for use on template and pattern work and can be used in hand-held and table-mounted routers. They have a shank mounted bearing which will run along and follow the template which is attached to the workpiece with the end result being an exact duplicate of the template itself. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10.
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • This range of single flute replacement tip cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. The TC tips are non reversible and are sold singularly.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • V Groover TCT

    £35.17£133.04
    DESCRIPTION Ideal for veining work, freehand decor for panels and useful for character lining work on sign writing applications in solid timbers. The angle ( measurement A ) is measured from the horizontal. TTVGC45SF-1/2, TTVGC45SF-1/4, TTVGC45SF-12, TTVGC60SF-1/2, TTVGC60SF-1/4, TTVGC60SF-12, TTVGC60SF-8 cut to a point. TTVGCB45-1/4, TTVGCB60-127-1/4 have a shank mounted bearing.  
    Select options This product has multiple variants. The options may be chosen on the product page Details
  • Select options This product has multiple variants. The options may be chosen on the product page Details