-
TCT Single Flute A high performance, single flute, cutter for extra clearance when cutting apertures and shaping work. The single flute gives a stronger backing support to the cutting edge. -
TCT Double Flute Shear action downcut to reduce breakout for longer life and improved performance. Pushes waste material away from the operator. -
TCT Double Flute Mini trimmers give a super fine finish. Ideal for cutting out small recesses in wall cladding for electrical fittings and suitable for trimming inlay flush and other trimming operations. Use TTTB22 Bearing for trimming overhanging countertops on undermount bowls. -
TCT Two Flute Bowl Aperture Trimmer Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. DESCRIPTION Use with 30mm guide bush or Bearing on shank for opening out tops for sinks and bowls. Also for most bevel operations. -
TCT Double Flute For edging sinks and vanity bowls. The special taper on the Bearing sleeve allows for perfect guide following around the inside of the bowl. -
TCT Double Flute For creating a 'step down' shadow line between bowl and sheet. -
TCT Double Flute Fitted with self-guiding Bearing for rounding over. See cutters TTXC301 and TTXC321 for complete rounding over. -
TCT Two Flute Box Cove For fine work to produce double radius in one pass, adjustable should material thicknesses vary. DESCRIPTION A further extension of the guttering cutter range with deeper cut for shallow fingerpull applications. Can also be used for cove cut on worktop upstands. For use with a template and guide bush for draining board grooves. Is suitable for producing grooves to take insulation rods. -
TCT Double Flute Primarily used to produce drain board channels. For use with template and guide bush. DESCRIPTION Primarily used to produce drain board channels. For window sections, designed to help displace water and moisture off window and door frames. Can also be used as soap dish cutter. For use with template and guide bush. -
TCT Double Flute 90 degree joint fabrication radius cutter, suitable for splashback and other 90 degree joints. -
TCT Double Flute Great care should be exercised when using this cutter to avoid 'cutter wander'. Use correct jig, template or side fence. Use a guide bush in conjunction with an offset template. -
TCT RPS Bevel Hole These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. DESCRIPTION These bevel hole cutters are specially developed to bevel an existing hole or to make new bevelled holes. TTXC906-18 and TTXC906-23 bevel plug cutters can be used to make accurate plugs for the holes produced by the TTXC901 range of bevel hole cutters. -
These cutter are double flute and they are non plunging with an outside fixing style for the use of profiling, the tips have 4 cutting edges so they can also be ramped down into workpiece. Tips are reversible and are sold in boxes of 10 -
A particular advantage to this replacement tip style over the conventional brazed variety is that the diameter remains constant. These double and single flute style flush trim router cutters are designed for use on template and pattern work and can be used in hand-held and table-mounted routers. They have a shank mounted bearing which will run along and follow the template which is attached to the workpiece with the end result being an exact duplicate of the template itself. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
This range are ideal for use on wood, plywood, MDF and other wood composites, plastics, and solid surface materials. Widely used for copy profiling and flush trimming, the replaceable tip design provides a constant diameter and the flexibility of instant tip changes whilst onsite. The L209-OH tip has one cutting edge and is non reversible, the others are reversible. Tips are sold in boxes on 10. -
A unique cutter that will trim the top and bottom edges of a panel simultaneously, the centrally mounted bearing follows the profile. Tips are reversible and are sold in boxes of 10. -
This range of single flute RT cutters are used to produce chamfers and V grooves on softwood, hardwood, MDF and other manmade materials. The design in allows a perfect V in the bottom of the groove. The tips are reversible and sold in boxes of 10. -
This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10. -
Angles are measured from the horizontal. Tips are reversible and are sold in boxes of 10. -
The cutters still give a fantastic finish, great longevity of use and of course can be re-sharpened, a superb cutter at a very competitive price. -
A range of lip and spur boring bits with 10mm diameter shanks that have a flat on one side and length adjusting screw in the end. Available with right hand or left hand rotation. -
DESCRIPTION A comprehensive range of straight fluted router cutters with diameters from 1.5mm to 50.8mm with parallel and internally threaded shank configurations. There are some left hand rotational cutters in this range. Part numbers starting with TTWLC are for use in inlay work and have a chisel point end. TTPH do not plunge. -
DESCRIPTION Special relief on the cutter body allows for deep slotting work. Suitable for plunging. Note:LH58L, LH58L2, LH34L, not to be used in a portable router. -
These router cutters are designed for use on template and pattern work, blind profiling and plunging They have a shank mounted bearing which will run along and follow the template which is attached to the work piece with the end result being an exact duplicate of the template itself. -
Widely used for copy profiling and flush trimming . Aluminium cutting reference numbers TTSIBGT90LK-1/2 , TTSIBGT90LK-1/4 Downward shear cutter action reference numbers TTBGT90LKS-1/2, TTBGT90LKS-1/4, TTBGT90LKS-12, TTBGT90LKS-6, TTBGT90LKS-8, TTBGT90S-1/4, TTBGT90S-6, TTBGT90S-8, cutters have a downward shear cutting action. Top and Bottom bearing guided reference numbers TBGT90LK1DB-1/2, TTBGT90LK2DB-1/2, TTBGT90LK2DB-12, TTBGT90LK2DB-4-1/2, TTBGT90LKDB-1/2, TTBGT90LKDB-8 TTBGT90LKSLP-1/4, TTBGT90SLP-1/4 have a low profile end screw for restrictive access applications. Oversize bearing cutters reference numbers TTIBGT63LK-B375-1/4, TIBGT63LK-B375-6 have an oversize bottom bearing for overhang trimming. TTSET1214-1/4 has a solid end bearing for heavy duty work. -
DESCRIPTION Ideal for veining work, freehand decor for panels and useful for character lining work on sign writing applications in solid timbers. The angle ( measurement A ) is measured from the horizontal. TTVGC45SF-1/2, TTVGC45SF-1/4, TTVGC45SF-12, TTVGC60SF-1/2, TTVGC60SF-1/4, TTVGC60SF-12, TTVGC60SF-8 cut to a point. TTVGCB45-1/4, TTVGCB60-127-1/4 have a shank mounted bearing. -
TCT Bevelled A range of various angles of beveled cutters designed to chamfer sections of timber, chipboard and MDF. DESCRIPTION The cutters with reference TTBCF have a tungsten carbide plunging centre tip The cutters with reference TTBC are for profiling only and do not plunge. Angles are measured from the vertical -
TCT Bevelled With Bottom Bearing A range of bevelled chamfer cutters with bottom guide bearing for large sections of timber, chipboard and MDF. -
TCT Chamfer With Guide Pin A range of 45 and 30 degree chamfer cutters designed with a fixed small diameter guide pin. DESCRIPTION Useful for internal work where the small diameter pin enables right angle corners to be included. Popular in the sign making industry as they can chamfer the edges of plastic materials . -
TCT Ovolo Used in conjunction with a side fence, most ovolo and rounding over operations can be produced with this extensive range. These cutters have plunging facility. -
DESCRIPTION Supplied with 2 bearings, 12.7mm and 16mm in diameter, two shapes can produced with one cutter by changing the bearing size. The 16 mm diameter bearing removes the bottom quirk. -
TCT Corner Ovolo Profiles and moulds in one operation. Ideal for aperture cutting, ie snooker table pockets, worktops and cover mouldings. DESCRIPTION WCO Type have plunge facility. WCOB Type have bearing. -
These cutters are the perfect solution to finishing cladding and corners on pillar covering or for enhancing square table legs or returns on wall unit furniture. The diameter of the bead is twice the value of the radius i.e. R=2mm the bead diameter is 4mm. -
DESCRIPTION A comprehensive range of Core Box, Cove, Radius, Guttering cutters with radii from 1.6mm to 25.4mm. Cutters with part number starting TTCBB have a shank mounted bearing fitted.
