-
TCT Adjustable Top and Bottom Chamfer with Bearing DESCRIPTION For bevelling and trimming the top and bottom edges of the workpiece. Adjust the four wing trimmer blocks with spacers for differing widths of material. Maximum material thickness 15mm for the DCB16 and is fixed Maximum material thickness 32mm, minimum material thickness 16mm for the BCS38. Maximum material thickness 36mm, minimum material thickness 19mm for the BGAC45. To extend the life of cutting edges use 26mm bearing.
-
This range of single flute RT cutters are used to produce chamfers and are ideal for V grooves on softwood, hardwood, MDF and other manmade materials. The design and the specially ground tip produce a perfect V in the bottom of the groove. Angles are measured from the vertical, i.e. a TTVGC60SFRT-1/2 has an inclusive angle of 120 degrees on the tool. Cutters come complete with one tip already installed, the L308 tips are reversible the others are non reversble. Tips are sold in boxes of 10.
-
Downturn Rebate Cutter Has many cutting and grooving uses in decorative and repair work. Particularly suitable for bowl replacement. Lower illustration shows method of removing bowl from worktop. DESCRIPTION To produce a 13mm rebate for the downturns on solid surface worktops. Fitted with a plastic sleeved bearing TTPB127.
-
TCT Cove Mould Bearing Guided Producing a quarter round on the edge of the workpiece these are ideal for detailing casework, doors and drawers, posts and columns. The cove also makes up one-half of the rule joint used on drop-leaf tables. DESCRIPTION These cutters come complete with TTB127 and TTB16 bearings. Matching rounding over cutters available for rule joints.
-
TCT Double Flute Primarily used to produce drain board channels. For use with template and guide bush. DESCRIPTION Primarily used to produce drain board channels. For window sections, designed to help displace water and moisture off window and door frames. Can also be used as soap dish cutter. For use with template and guide bush.
-
TCT Groover Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15 and 20mm strip. DESCRIPTION Consists of Groover, Bearing and Arbor. Can be supplied for 10, 15, 20 and 25mm strip. For slotting doors with a portable routing machine, using a Guide Bearing to give the correct cutting depth of 4mm. Suits Therma Seal Intumescent Strip.
-
TCT Biscuit Joint Biscuit Joint Slotter with Arbor self guided. Comes with 3 interchangeable bearings to produce slots for the popular biscuit sizes of 0,10 and 20. Ideal for hardwood, softwoods, ply, MDF and chipboard. DESCRIPTION Z=Number of flutes. RPM=Maximum revolutions per minute Groove Depth with various bearings are as follows TTB15 = 12.5mm, TTB19 = 10.5mm, TTB23 = 8.5mm.
-
TCT Two Flute Box Cove For fine work to produce double radius in one pass, adjustable should material thicknesses vary. DESCRIPTION A further extension of the guttering cutter range with deeper cut for shallow fingerpull applications. Can also be used for cove cut on worktop upstands. For use with a template and guide bush for draining board grooves. Is suitable for producing grooves to take insulation rods.
-
BALL GROOVER SINGLE FLUTE TCT A range of single flute ball slot cutters designed for pipe and cable laying into timber and MDF. DESCRIPTION Important - cut neck slot first, do not run on neck but use a side fence or guide. NB The neck does not cut. Suggested cutters for neck slot: TTM716 for TTTSB127 neck diameter 6.5mm; TTM1020 for TTTSB254 neck diameter 9.5mm; TTM1325 for TTTSB32 neck diameter 12.7mm
-
This range of precision credit card stones are 1.6mm thickness means no flexing as in cheaper thinner products and are made with Monocrystaline Diamonds to give the maximum performance possible . The stones range from Extra Coarse / Coarse (180/300 grit) perfect for sharpening roughing gouges, hss hollow inserts/corning inserts, through to the woodcarvers stone which is Fine / Extra Fine (600 / 1000 grit) for precision honing and gaining bthe keenest edge on small carving tools etc. Don't forget to buy your TITMAN EDGE lapping fluid to guarantee a 5 year warranty on the stones.
-
This range of bead cutters produce mouldings to highlight features such as fascia rails, chair backs or decorative sections 'planted' on bedroom furniture to bring a line and feature to a continuous layout. TTDSB4 is a sunken flute cutter with a shallow radius to produce a soft effect. An ideal cutter to produce fluted pillars, for fire surrounds and 'gable ends' on bedroom furniture. Useful cutter to cut on a glue joint to hide the glue line. TTDSB5 is a sunk bead mould perfect for finishing wall unit facias and cover moulds on window sections. TTDSB7 is ideal for fluting or decorating solid surrounds.
-
This range of double sided diamond bench stones range from extra Coarse & Fine 180/ 600 to the Classic Proffesional Stone which is extra fine & coarse 1000/300 grit. These Stone have a precision ground substrate ground to +/- 0.0005" and are manufactured with Monocrystaline Diamonds, making them perfect for precise sharpening of all types of tooling from Plane Irons to solid carbide tips. The Stone have clearly marked grit sizes on their surface and the extra course stone has unique clearance channels to clear away swarf and produce a keen edge fast and efficiently. The smooth continual diamond surface on the fine sides prevents snagging when sharpening small or pointed tooling. Don't forget to buy your TITMAN EDGE lapping fluid to guarantee a 5 year warranty on the stones.